Standard Accessories; Battery Removal/Installation - Hitachi DS 14DJL Bedienungsanleitung

STANDARD ACCESSORIES

1 Plus driver bit (No. 2) ...................... 1
2 Charger (UC18YKSL) .............................. 1
DS14DJL
(2LEGK)
3 Battery (BSL1415 or BSL1815) ........ 2
DS18DJL
4 Plastic case ....................................... 1
(2LEGK)
5 Battery cover .................................... 1
1 Plus driver bit (No. 2) ...................... 1
DS14DJL
2 Charger (UC18YKSL or UC18YFSL) ...... 1
(2LFGK)
3 Battery (BSL1425 or BSL1825) ........ 2
(2LFRK)
DS18DJL
4 Plastic case ....................................... 1
(2LFGK)
5 Battery cover .................................... 1
(2LFRK)
6 Cordless torchlight (UB18DAL) ...... 1
1 Plus driver bit (No. 2) ...................... 1
2 Plastic case ....................................... 1
DS18DJL
Wituout chager, battery, torchlight and
(NNK)
battery cover.
1 Plus driver bit (No. 2) ...................... 1
DS14DJL (NN)
Wituout chager, battery, plastic case,
DS18DJL (NN)
torchlight and battery cover.
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
Battery
BSL1415, BSL1425
BSL1815, BSL1825
Hook (with screw)
Optional accessories are subject to change without notice.
Before
charging
While
charging
Charging
Pilot lamp
complete
(red)
Overheat
standby
Charging
impossible
Indications of the pilot lamp
Lights for 0.5 seconds. Does not light for 0.5
seconds. (off for 0.5 seconds)
Blinks
Lights continuously
Lights
Lights for 0.5 seconds. Does not light for 0.5
Blinks
seconds. (off for 0.5 seconds)
Lights for 1 second. Does not light for 0.5
seconds. (off for 0.5 seconds)
Blinks
Lights for 0.1 seconds. Does not light for 0.1
seconds. (off for 0.1 seconds)
Flickers
APPLICATIONS
Driving and removing of machine screws, wood
screws, tapping screws, etc.
Drilling of various metals
Drilling of various woods

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch
(2 pcs.) to remove the battery (See Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (See
Fig. 2).
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a
receptacle, the pilot lamp will blink in red (At 1-
second intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3.
3. Charging
When inserting a battery in the charger, charging will
commence and the pilot lamp will light up
continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals) (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown in
Table 1, according to the condition of the charger or
the rechargeable battery.
Table 1
English
Battery overheated.
Unable to charge.
(Charging will commence
when battery cools)
Malfunction in the
battery or the charger
9