Important Assembly Information; Technical Data - Supra TERTIO 76 VL1 Installations- Und Bedienungshandbuch

You have just purchased an appliance from our range. We would like to congratulate you on your choice. This appliance has been
carefully designed. In order to get the very best out of it, we would advise you to request the services of one of our specialists. This will
ensure that the installation is made in accordance with good practices and will guarantee the best operating and safety conditions,
bearing all the responsibility for the final installation.
Before lighting the fire for the first time, please read these installation and operating manual carefully. Retain the manual and warranty
(which indicates the model and serial No.). The person performing the installation work shall be fully liable for any failure to comply with
the instructions set out in these two documents.
Your chimney «draws well», but you are unsure of the draught value. The chimney draught is measured in Pascal (Pa). The
inserts, fireboxes and stoves have been designed, optimised and manufactured in accordance with standards NF EN 13229 (or
NF EN 13240) to operate connected to a chimney with a draught of 12 Pa. It frequently happens (in more than one in two
chimneys) that the draught is far too high (over 20 Pa) due to the fact that the chimney is either too high or due to the flue
liner. In this case, the appliances will operate in abnormal conditions which may lead to:
- Excessive wood consumption: this can be three times as much as an appliance with a draught of 12 Pa.
- A fire that "keeps going out" and burns too quickly while producing insufficient heat.
- A quick and inevitable deterioration of the appliance (cracks in the cast iron panels or in the refractory bricks)
- A voided warranty.
To avoid all these problems, there is only one solution!
Get a professional to check the chimney draught (with the appliance operating) and, if it is above 20 Pa, then install a damper
or an adaptor at the flue connection.

1. TECHNICAL DATA

FIREPLACE INSERT
Stove category
Rated heat output (1)
Operating mode
Average flue gas temperature with the door
closed
Efficiency
Seasonal efficiency
CO concentration (13% 02)
CO2 concentration (13% 02)
Dust concentration (13% 02)
VOC
NOX
Fuel
Log size
Nominal load per hour approx.
Refuelling
Prohibited fuels
Approx. flue gas mass flow
Characteristics of the flue pipe
Chimney flue minimum dimensions
Flue pipe nominal diameter
Ø min. flue lining or insulated metal duct
Diameter of hot air distributor outlet
Minimum height above the hearth
Ventilation of the room
Draught (10 Pa = 1 mm CE)
Nominal efficiency
Performance in slumber mode (min.
permitted)
Max. permitted
Net weight (gross + 25 kg)
Nameplate
Air connection collar
Accessories supplied
Cold hand key, heat-insulated glove, hot air collars
Option available
220/230 V Fan kit
Hot air pipe (to fit inside hearth)
Decorative façade
Feet
(1) Rated power in operation with the door closed, wood fuel, according to the tests performed under standard EN 13229.
(2) DTU 24.1 covering flue ducting, DTU 24.2 covering chimneys equipped with a closed stove; NF EN 13229 covering solid fuel burning
stoves. (Available at AFNOR).
- IMPORTANT -

- IMPORTANT ASSEMBLY INFORMATION -

TERTIO 55
6 kW
243 °C
76 %
62 %
0.2 %
8.38 %
3
90 mg/Nm
3
322 mg/Nm
3
114 mg/Nm
33 cm
2 kg/h
7 g/s
Male 153 mm
153 mm
60 kg
Option KT 55
2
-
Option PS 55
TERTIO 67 TERTIO 67 VL1
Intermittent
9 kW
Only with the door closed
357 °C
70.7 %
60.7 %
0.25 %
9.6 %
- -
- -
- -
Wood
50 cm
2.9 kg/h
1 h
All the rest, including coal and its derivatives
9.8 g/s
20 x 20 cm
Male 180 mm
125 mm
4 m
1.2 dm²
12 Pa ± 2 Pa
6 Pa ± 1 Pa
20 Pa
99 kg 94 kg
On the ash box
Ø 75
Option KT 67
4
Option PS 67
TERTIO 76 TERTIO 76 VL1
9.5 kW
325 °C
75 %
65 %
0.104 %
9.61
3
20 mg/Nm
3
92 mg/Nm
102 mg/Nm
50 cm
2.9 kg/h
9 g/s
Male 200 mm
180 mm
150 mm
110 kg
Option KT 76
4
Decade
Option PS 76
3
95 kg