Connections - Denon ADV-1000 Bedienungsanleitung

ENGLISH
(6) Sound output from this unit digital audio output connectors
2 When a disc is played on the ADV-1000
Audio recording format
Digital out : Normal
Dolby Digital
Digital out : PCM conversion
Digital out : Normal
DTS
Digital out : PCM conversion
Digital out : Normal
DVD video
MPEG audio
DVD audio Digital out : PCM conversion
(video part only)
LPCM conversion mode : OFF
48 kHz
LPCM conversion mode : ON
96 kHz LPCM conversion mode : ON
CP : ON LPCM conversion mode : OFF
CP : OFF LPCM conversion mode : OFF
Video CD MPEG 1
Music CD Linear PCM
MP3 CD MP 3
• Linear PCM audio is the signal recording format used for music CDs.
While the signals are recorded at 44.1 kHz/16 bit for music CDs, for DVDs they are recorded at 48 kHz/16 bit to 96 kHz/24 bit,
providing higher sound quality than music CDs.
(7) Speaker system connections
• Use speaker cords with twisted wire cores and a diameter
of 0.6 to 1.5 mm. Never use cords thicker than 1.5 mm or
single-wire cords, as they may damage the speaker
terminals.
• Be sure to interconnect the polarities of the terminals on the
speakers and main unit (≈ to ≈, √ to √).
• When making connections, be careful that none of the core
wires of the speaker cords stick out and touch neighboring
terminals, other speaker cords or the rear panel.
• Speakers with an impedance of 6 to 16 Ω/ohms can be
connected for use as center and surround speakers.
Connection the speaker terminals
1. Push the lever.
8
Refer to
Settings Digital audio data output
page
Dolby Digital bitstream
2 channels PCM data (48 kHz/16 bit)
44
DTS bitstream
DTS bitstream
2 channels PCM data (48 kHz/16 bit)
44
2 channels PCM data (48 kHz/16 bit)
48 kHz/16 ~24 bit PCM
48 kHz/16 bit PCM
44 48 kHz/16 bit PCM
48 kHz/16 bit PCM (when copy-protected)
96 kHz PCM (when not copy-protected)
44.1 kHz/16 bit PCM
44.1 kHz/16 bit PCM
32 ~ 48 kHz/16 bit PCM
NOTE:
NEVER touch the speaker terminals when the power is
on.
Doing so could result in electric shocks.
• The protector circuit may be activated if the set is played for
long periods of time at high volumes when speakers with an
impedance lower than the specified impedance are
connected.
2. Insert the cord. 3. Return the lever.

Connections

• When making connections, also refer to the operating instructions of the other components.
FRONT SPEAKER CENTER SPEAKER SURROUND SPEAKER
SYSTEMS SYSTEM SYSTEMS
(L)
(L) (R)
IMPEDANCE SUB
R L R L
CENTER 6 16 WOOFER
FRONT SURROUND
SPEAKER SYSTEMS
Protector circuit
• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the
speakers under circumstances such as when the output of the power amplifier is inadvertently short-
circuited and a large current flows, when the temperature surrounding the unit becomes unusually high,
or when the unit is used at high output over a long period which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED
flashes. Should this occur, please follow these steps: be sure to switch off the power of this unit, check
whether there are any faults with the wiring of the speaker cables or input cables, and wait for the unit to
cool down if it is very hot. Improve the ventilation condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the
ventilation around the unit, switch off the power and contact a DENON service center.
Note on speaker impedance
• The protector circuit may be activated if the set is played for long periods of time at high volumes when
speakers with an impedance lower than the specified impedance (for example speakers with an
impedance of lower than 4 Ω/ohms) are connected. If the protector circuit is activated, the speaker output
is cut off. Turn off the set's power, wait for the set to cool down, improve the ventilation around the set,
then turn the power back on.
SUB WOOFER
(R)
Connector jack for
subwoofer with built-in
amplifier (super
woofer), etc.
LOOP ANT.
S VIDEO VIDEO
MON.OUT IN IN IN IN OUT MON.OUT IN IN IN IN OUT
TV/DBS V.AUX VCR TV/DBS V.AUX VCR
FM COAX. 75
L AM
PRE OUT
R
AV 1
SUB WOOFER IN OUT IN IN IN OUT IN IN
CDR/ TV/DBS V.AUX VCR TV/DBS V.AUX
TAPE
AUDIO DIGITAL(OPTICAL)
• Precautions when connecting speakers
If a speaker is placed near a TV or video monitor, the
colors on the screen may be disturbed by the speaker's
magnetism. If this should happen, move the speaker
away to a position where it does not have this effect.
OUT