Surround Playback - Denon ADV-1000 Bedienungsanleitung

ENGLISH
14

SURROUND PLAYBACK

(1) Before playing with the surround function
• Adjustments using the test tones can only be performed in
the "Auto" mode and are only valid for the Auto decode
Surround modes. The adjusted levels are automatically
stored in the memory.
POWER
VCR POWER
CLEAR 7 8 9
TV
TV POWER TV POWER
CH TV/VCR SLEEP
CALL +10 0
DISPLAY RETURN INPUT MODE SURROUND
MENU FUNCTION
2 2
ENTER
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
RDS PTY CT RT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
1,3
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
1
Press the TEST TONE button.
T.TONE
Remote control unit
2
Test tones are output from the different speakers. Use
the channel volume adjust buttons to adjust so that the
volume of the test tones is the same for all the
speakers.
• The channel to be adjusted can be changed using the
CH.SELECT button and the ( and
buttons on the remote control unit during the
adjustments using the test tones.
Remote control unit
3
After adjusting using the test tones, adjust the channel
levels either according to the playback sources or to
suit your tastes, as described below.
T.TONE
Remote control unit
22
• Even after adjusting using the test tones, the various
channels can be adjusted using the procedure described
below to suit the program source and your preferences.
POWER
VCR POWER
CLEAR 7 8 9
TV
TV POWER TV POWER
CH TV/VCR SLEEP
CALL +10 0
DISPLAY RETURN INPUT MODE SURROUND
MENU FUNCTION
2
ENTER
MODE
VOLUME
BAND
MUTE
CH SHIFT
NTSC/PAL STATUS
TU MEMO
SUB TITLE AUDIO ANGLE TOP MENU
RDS PTY CT RT
PROG/DIRECT REPEAT A-B REPEAT RANDOM
CH.SELECT T.TONE SDB/TONE SURR.PARA
1
SETUP CDR/MD/TAPE TUNER/TV/VCR DVD
REMOCON MODE
1
Select the speaker whose level you want to adjust.
• The channel switches as shown below each time the
button is pressed.
CH.SELECT
Remote control unit
FRONT L FRONT R
CENTER
SUBWOOFER SURROUND L SURROUND R
) cursor
2
Adjust the volume level of the selected speaker while
the channel level is displayed.
Remote control unit
[1] 2-channel mode settings
• In the auto decode mode, it is possible to automatically conduct multi-channel playback in the Dolby Digital or DTS surround
mode or play in the stereo 2-channel mode (AUTO STEREO mode: factory default setting). For 2-channel input signals, one of
four play modes can be set with the 2-channel mode setting (Auto Stereo, Dolby Pro-Logic II Cinema, Dolby Pro-Logic II Music
and Dolby Pro-Logic).
When the function is set to VCR, CDR/TAPE or TUNER, the "Auto Stereo" 2-channel mode cannot be selected. To
play in stereo, set the surround mode to "STEREO" (page 19).
POWER
VCR POWER
2
TV POWER
CALL +10
DISPLAY RETURN INPUT MODE SURROUND
MENU
3
ENTER
MODE
BAND
CH
TU
SUB TITLE AUDIO
RDS
PROG/DIRECT REPEAT A-B
T.TONE
CH.SELECT
SETUP CDR/MD/TAPE TUNER/TV/VCR
1
Set the surround mode to "AUTO DECODE".
• "AUTO DECODE" is displayed, then the normal
display reappears.
SURROUND FUNCTION
MODE
/ SELECT
\
Main unit Main unit
If the mode is set to anything other than AUTO
DECODE, the AUTO DECODE mode can be set
using the AUTO DECODE/2CH MODE button on
the main unit.
2
Press the SURR.PARA button on the remote control
unit and select the 2-channel decode mode.
This can be selected when the digital input consists
of no signal, PCM signals, Dolby Digital 2-channel
signals, as well as when the analog input is
selected.
1
3
Select the desired 2-channel
decode mode using the (
) cursor buttons on the
remote control unit.
• The mode switches as follows
each time one of the buttons
1, 3 1
is pressed:
0
1
AUTO ST
FUNCTION
PRO LOGIC
3
If the AUTO DECODE/2CH MODE button on the
main unit is pressed when the mode is already set
to AUTO DECODE, the mode switches to the 2-
VOLUME
channel mode. The mode switches as follows each
MUTE
SHIFT time the button is pressed.
NTSC/PAL STATUS
MEMO
ANGLE TOP MENU
AUTO STEREO
PTY CT RT
REPEAT RANDOM
PRO LOGIC
SDB/TONE SURR.PARA
2
DVD
The Auto Stereo mode can be selected when the
function is set to DVD, TV/DBS or V.AUX.
Once the surround parameters have been set, stop
operating buttons. After several seconds the display
returns to normal and the settings are automatically
SURROUND
validated.
NOTES:
• The 2-channel decode mode cannot be set when Dolby
Remote control unit
Digital 5.1-channel signals or DTS signals are being input.
• The 2-channel decode mode is stored separately for the
DVD, TV/DBS and V.AUX modes.
SURR.PARA
Remote control unit
and
Remote control unit
PL II CINEMA
PL II MUSIC
PLO LOGIC II C
PLO LOGIC II M