Funktionstastenbelegung für Digitalmodelle / Function keys for digital models
Funktionszuordnung Decoder ohne Sound DH22-4 (DCC/SX1/SX2/Motorola/DC/AC) /
Function assignment decoder without sound DH22-4 (DCC/SX1/SX2/Motorola/DC/AC)
BRAWA-Nr.: 0014765.99 BR01
Fkt.
Beschreibung
Fct.
Description
F0
Hauptlicht /
Main light
F1
Licht vorn (Rauchkammer) ausschalten /
Light at front side out
F2
Licht hinten (Tender) ausschalten /
Light at rear side out
F3
Licht Führerstand / Light drivers cabin
F4
Rangiergang und Rangierlicht /
Shunting trip
F5
Raucherzeuger / Smoke injector
Zusatz-Information
Alle Ausführungen
Die Lok ist mit einer PluX22Schnittstelle gemäß NEM 658
ausgestattet. Die PluX22-Schnittstelle befindet sich in der
Lok im Stehkessel. Die elektrische Verbindung zwischen Lok
und Tender erfolgt über einen 10poligen Kontaktstecker.
Der Motor (Antrieb) ist im Tender eingebaut.
Version: Basic+ (analog DC)
Im analogen Fahrbetrieb ist der Lichtwechsel 2 x weiß bzw.
3 x weiß (je nach Modellausführung) aktiv.
Über einen Schiebeschalter kann auf dem analogen Brü
ckenstecker (siehe Bild) bei Bedarf das Licht im Führerstand
eingeschaltet werden. Beim Einbau eines PluX22Decoders
sind die Funktionen gemäß Tabelle „Funktionszuordnung
Decoder ohne Sound DH224" verwendbar.
Version: Basic+ (analog AC)
Im analogen Fahrbetrieb ist der Lichtwechsel 2 x weiß bzw.
3 x weiß (je nach Modellausführung) aktiv.
Durch eine Veränderung der CVProgrammierung vom
Decoder können weitere Funktionen (wie z.B. das Licht im
Führerstand) für den analogen Betrieb aktiviert werden.
Für den Austausch des Decoders beachten Sie bitte auch
die Punkte „Belegung der physikalischen Ausgänge" und
„Digitalisieren der analogen Basic+Ausführung".
Version: Basic+ (digital AC)
Die Lok ist im Digitalbetrieb auf die Betriebsart DCC mit
der Adresse 3 ab Werk eingestellt. Im digitalen Betrieb
stehen die Funktionen F1 bis F4 (F5 ist optional für den
Rauchgenerator vorgesehen) zur Verfügung (siehe Tabelle
„Funktionszuordnung Decoder ohne Sound DH224").
Mapping
Anmerkung
-CV
Note
LV/LR
33/34
mit Fahrtrichtung wechselnd, nur 2/3 x weiß /
145
main light is changing with driving direction 2 or 3 white lights
146
LV
113
LR
114
AUX2
37
38
145
146
AUX3
39
für den Einbau eines Raucherzeugers vorbereitet /
ready for a smoke injector to be installed
Additional Information
All versions
The locomotive is equipped with a PluX22 interface accor
ding to NEM 658. The Plux22 interface is located inside
the outer firebox. The electrical connection between the
locomotive and the tender is made by a 10pin connector.
The Motor is assembled into the Tender.
Version: Basic + (analog DC)
In analog mode, the standard change of light is 2x white or
3x white is activ, depending on the Loco version.
There is a slide switch located on the analog plug (see pic
ture) which ellows to turn on or off the Drivers Cabin Light.
When installing a PluX22 decoder, the functions according
to the table „Function assignment decoder without sound
DH224" can be used.
Version: Basic+ (analog AC)
In analog mode with decoder, the standard change of light,
2x white or 3x white is activ, depending on the loco version.
Trough a change of CV values of the decoder installed, addi
toinal functions like e.g. Drivers Cab Light can be activated
for usage in analoge mode.
When changing a decoder, please also note the points
„Assignment of the physical outputs" and „Digitizing the
analog Basic + version".
Version: Basic+ (digital AC)
In digital mode, factory setting for this loco is digital adress
3 in DCC mode. In digital mode, the functions F1 to F4 are
available (F5 is optional for usage of the Smoke generator)
please refer to the table „function asignment Decoder
withouit sound DH224"
5