Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Silence function
2s
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function(some units).
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
FP function
Press this button 2 times during one second under HEAT Mode and setting temperature of
16 C/60 F or 20 C/68 F(for model RG10A10(B2)/BGEF).
O
O
O
O
2
The unit will operate at high fan speed (while
compressor on) with temperature automatically
set to 8 C/46 F.
Note: This function is for heat pump air conditioner only.
Press this button 2 times under HEAT Mode and setting temperature of 16 C/60 F to activate
the FP function. Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel
this function.
LOCK function
5s
5s
+
Press together Clean button and Boost button at the
Clean
Boost
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
58
SET function
SET
SET
or
Press the SET button to enter the function setting, then press SET button or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
Press the SET button to scroll through operation functions as follows:
Breeze Away (
)
Fresh (
)
Sleep(
*
*
[ ]: If your remote controller has Breeze Away button or Fresh button, you can not use the SET
*
button to select the Breeze Away or Fresh feature.
Breeze Away function(
) (some units) :
This feature avoids direct air flow blowing on the
body and makes you feel indulging in silky
coolness.
NTOE: This feature is available under cool,
Fan and Dry mode only.
FRESH function(
) (some units) :
When the FRESH function is initiated, the
Ionizer/Plasma Dust Collector or UV lamp
(depending on models) is energized and will
help to remove pollen and impurities
from the air.
Sleep function(
) :
The SLEEP function is used to decrease
,
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
, ,
,,
For the detail, see sleep operation in
,
,,
, ,
USER S MANUAL.
Note: The SLEEP function is not available
in FAN or DRY mode.
or TEMP
)
Follow Me(
)
AP mode(
)
Follow me function(
):
The FOLLOW ME function enables the remote
control to measure the temperature at its
current location and send this signal to the
air conditioner every 3 minutes interval.
When using AUTO, COOL or HEAT modes,
measuring ambient temperature from the
remote control(instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
NOTE: Press and hold Boost button for
seven seconds to start/stop memory
feature of Follow Me function.
If the memory feature is activated, On
displays for 3 seconds on the screen.
If the memory feature is stopped, OF
displays for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the Follow
me function.
AP function(
)(some units) :
Choose AP mode to do wireless network
configuration. For some units, it doesn't
work by pressing the SET button. To enter
the AP mode, continuously press the LED
button seven times in 10 seconds.
59
OK
,
,
,
,
,
,
,
,
Werbung
Kapitel
Inhaltsverzeichnis
