System Settings
DMX Address
001
Mode
DMX 22CH
Settings
System Info
E. DMX MODE (DMX)
Three different DMX modes are available for selection: 5-channel, 13-channel and 22-channel (DMX 05CH, 13CH, 22CH). The setting is made as
previously explained in point D. SETTING OPERATING MODE. You will find tables with the channels of the different DMX modes in this manual under
DMX CONTROL.
Mode DMX 22CH
F. SLAVE MODE (Slave)
The setting is made as previously explained in point D. SETTING OPERATING MODE.
Connect the slave and the master unit (same model) with a DMX cable. Enable one of the standalone modes (Auto, Sound, Static) in the master unit.
Now the slave unit follows the master unit.
Mode
Slave
G. AUTO MODE (Prog1 - Prog8)
The 8 various auto programs consist of a sequence of fixed programmed colour, gobo and motion sequences.
Pressing the MODE button will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "Mode" (dark back-
ground) and confirm by pressing ENTER. The digits which show the operating mode change their colour to red, and you can use the + and - buttons
to select the desired Auto operating mode. Confirm 2x with ENTER and select one of the 8 Auto programs (Prog1 - Prog8) using the + and - buttons,
confirm with ENTER and select the "AutoSpeed" menu item to adjust the program speed as required. Press ENTER to confirm, and adjust the speed
from 000 to 255 by using the + and - buttons. Confirm with ENTER and press the MODE button 3x to return to the main display.
Mode
Auto
Auto Mode
Auto
Prog 8
AutoSpeed
225
H. MUSIC CONTROL (Sound)
Pressing the MODE button will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "Mode" (dark back-
ground) and confirm by pressing ENTER. The digits which show the operating mode, change their colour to red, and you can use the + and - buttons
to select the desired Music control mode (Sound). By pressing ENTER to confirm, the microphone sensitivity can now also be adjusted using the +
and - buttons (Sen00% = minimum sensitivity, Sen99% = maximum sensitivity). Confirm with ENTER and press the MODE button 2x to return to the
main display. Now the spot is controlled by the built-in microphone and follows the beat of the music.
Mode
Sound
Mode Sen99%
I. STATIC MODE (Static)
In the same way as with a DMX control unit, the static mode allows you to adjust all functions such as Pan, Tilt, colour and gobo wheel, and strobe
directly on the device applying values from 000 to 255. Thus, a scene can be created without an additional DMX controller. Pressing the MODE button
will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "Mode" (dark background) and confirm by
pressing ENTER. The digits which show the operating mode, change their colour to red, and you can use the + and - buttons to select the desired static
mode (Static). After you have confirmed with ENTER, the parameters can be selected using the arrow buttons (see list). Press ENTER. The value of the
parameter can now be changed using the + and - buttons. Confirm the input with ENTER. Once all of the parameters have been set as required, press
the MODE button several times to return to the main display.
Mode
Static
Static
Pan
Pan fine
Tilt
Tilt fine
Strobe
Dimmer
000
-
255
0% to 100%
000
-
255
0% to 100%
000
-
255
0% to 100%
000
-
255
0% to 100%
000
-
005
Strobe open
006
-
010
Strobe closed
011
-
033
Puls Random, slow -> fast
034
-
056
Ramp up Random, slow -> fast
057
-
079
Ramp down Random, slow -> fast
080
-
102
Random Strobe Effect, slow -> fast
103
-
127
Strobe Break Effekt, 5s.....1s (Short burst with break)
128
-
250
Strobe slow -> fast <1Hz - 20Hz
251
-
255
Strobe open
000
-
255
0% to 100%
17