Use; Single-Phase Version - Femi GOLD Gebrauchsanleitungen Und Wartung

3.5 ADJUSTMENT OF BEARING BRACKET (Fig. 8)
JUST FOR CIRCULAR SAW
Loosen the handwheels 36 and slide the bracket 17, aligning
the index 37 on the bearing with its corresponding position
on the graduated scale on the work surface.
This position corresponds to the actual distance of the bearing
bracket rest from the centre line of the blade.
3.6 WEDGE REGULATION
To ensure the dividing wedge is in the correct position, keep
it at a distance of between 3mm - 8mm from the tooth of the
blade. Should this not be the case, loosen the screw which
holds it attached to the arm and move it to the aforementioned
distance (Fig. 17).
4

USE

After having performed all the above procedures and
operations, you may begin cutting.
HAZARD:
Always keep hands away from the cutting area and
do not try to approach it when the machine is
running.
4.1 USE AS A CUTTING-OFF MACHINE
(cutting on the lower work surface) (Fig. 9)

SINGLE-PHASE VERSION

- Release the head, by unscrew the block pin 19.
- Raise the machine head as far as possible.
- Secure the workpiece firmly against the angular bearings
33 of the base with your left hand, thus ensuring absolute
immobility during cutting.
- Put your right hand on the handgrip 1 and press the button
9 in order to release the head.
- Actuate the motor by pressing first the main switch release
device 14 and then the main switch start button 2 on the
handgrip.
- Lower the head and gradually bring the blade into contact
with the workpiece.
- Complete cutting and raise the head to its original
position.
- Turn off the motor by release the main switch button 2.
THREE-PHASE VERSION (Fig. 17)
Press button 55 of main switch.
Once you have completed all the procedures and operations
described so far, you may start the working processes.
To perform the cut, move to the front of the machine and grip
the handgrip with your right hand.
HAZARD: Keep your left hand away from the cutting
area and on no account try to reach it when cutting
is in process.
Using the index finger of your right hand, press the run button
2 and gradually lower the machine body until it comes lightly
into contact with the part to be cut.
Now begin to apply gradual pressure on the part and complete
the cut.
Always release button 2 between one cutting operation and
another, while you are positioning the part. do not try to block
it or alter its functional characteristics in any way.
14
4.2 USE AS A CIRCULAR SAW
(cutting on the upper work surface) (Fig. 10)
HAZARD:
When working on the upper surface, it is absolutely
necessary to install the lower safety guard supplied.
HAZARD:
The machine is equipped with a pusher the
dimensions and shape of which are in compliance
with the Safety Standards (Fig. 16). When the
machine is used as DISK SAW (thus using the upper
table for the machining operations), such fitting
MUST absolutely be used.
Hold pusher from side A while side B, equipped
with different steps to match different thickness
sizes, must be put in contact with the piece to be
cut as shown in the figure. The piece to be cut can
be pushed by means of the pusher which
simultaneously drives and rest it on square C thus
enabling to keep hands away from the blade cutting
area.
- When the motor is off, lower the machine head and block
it by means of the block pin 19.
- Adjust the height of the upper work surface according to
the cutting height desired and adjust the bearing bracket
as described in the paragraph "ADJUSTMENTS".
- Check that the removable upper shield is not faulty: after
having lifted it slightly, it must return to its orginal position,
covering the blade completely.
- Start the motor as described at point 4.1, and lock the
main switch in "ON" position by means of the locking
device 21 in the lower zone of the handgrip.
- Place the workpiece to be cut on the work surface, placing
it laterally against the bracket and then move the workpiece
slowly and gradually towards the blade.
CAUTION:
The workpiece must always be held firmly, paying
attention not to hold it near the cutting area.
- To turn off the machine, push the start button 2 of the
main switch, automatically release the locking device 21.
4.3 INSTALLATION AND/OR REPLACEMENT OF THE
BLADE (Fig. 11)
HAZARD:
This procedure must be carried out only after having
turned off the machine's motor by by release the
main switch button 2.
- Release the movable shield 11 by pressing the pawl 37
and simultaneously raising the shield so as to uncover
the blade, then lift the table up to its maximum height.
- Raise the upper surface as high as possible.
- Remove the protection plug of the blade-holding shaft
from the cover of the electronic box.
- Use the two Allen wrenches supplied: insert the one for 6
mm. socket-head screws in the terminal 38 of the driving
shaft and the one for 6 mm. socket-head screws in the
blade's fixing screw 39; then loosen the screw, keeping
in mind that the screw thread is left-handed.
- Remove the external flange 40, remove the blade by
sliding it out from the lower part of the head and install a
new blade.
- Ensure that the blade's teeth are oriented in the direction
of the arrow on the blade itself.
- Then, remount the outer flange 40, tighten the screw 39
firmly, using the Allen wrenches supplied.