Makita UR002G Betriebsanleitung Seite 22

Automatic Torque Drive Technology
When you turn on the Automatic Torque Drive
Technology (ADT), the tool runs at optimum rotation
speed and torque for the condition of grass being cut.
To start ADT, press and hold the reverse button until the
ADT indicator turns on. After that, tap the main power
button to select the cutting tool attached to the tool. Light
the lamp beside marking to select cutter blade and plastic
blade, marking to select nylon cutting head.
To stop ADT, press and hold the reverse button until the
ADT indicator turns off.
► Fig.11: 1. marking 2.
indicator 4. Main power button 5. Reverse
button
Indicator Mode
ADT
(Cutter blade)
ADT
(Nylon cutting
head)
Reverse button for debris removal
WARNING:
Switch off the tool and remove
the battery cartridge before you remove entan-
gled weeds or debris which the reverse rotation
function can not remove. Failure to switch off and
remove the battery cartridge may result in serious
personal injury from accidental start-up.
This tool has a reverse button to change the direction of rotation.
It is only for removing weeds and debris entangled in the tool.
To reverse the rotation, tap the reverse button and pull the
switch trigger while depressing the lock-off lever when the cut-
ting tool is stopped. The speed indicators and ADT indicator
start blinking, and the cutting tool rotates in reverse direction
when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the cutting tool stops.
► Fig.12: 1. Speed indicator 2. ADT indicator
3. Reverse button
NOTE: During the reverse rotation, the tool operates
only for a short period of time and then automatically
stops.
NOTE: Once the tool is stopped, the rotation returns
to regular direction when you start the tool again.
NOTE: If you tap the reverse button while the cutting
tool is still rotating, the tool comes to stop and to be
ready for reverse rotation.
marking 3. ADT
Cutting tool Rotation
speed
Cutter blade 3,500 - 6,500
-1
Plastic blade min
Nylon cutting 3,500 - 6,500
-1
head min
Electric brake
This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after the switch trigger
is released, have the tool serviced at our service center.
CAUTION:
This brake system is not a substi-
tute for the protector. Never use the tool without
the protector. An unguarded cutting tool may result
in serious personal injury.
Electronic function
Constant speed control
The speed control function provides the constant rota-
tion speed regardless of load conditions.
Soft start feature
Soft start because of suppressed starting shock.
ASSEMBLY
WARNING:
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
in serious personal injury from accidental start-up.
WARNING:
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonal injury from accidental start-up.
Installing the handle
For UR002G
1. Insert the shaft of the handle into the grip. Align
the screw hole in the grip with the one in the shaft.
Tighten the screw securely.
► Fig.13: 1. Grip 2. Screw 3. Shaft
NOTICE:
Note the direction of the grip. The
screw holes will not be aligned if the grip is not
inserted in the correct direction.
2. Adjust the handle position, and then tighten the
knob to fix the handle.
► Fig.14: 1. Knob
For UR003G
1.
Attach the upper and lower clamps on the damper.
2. Put the handle on the upper clamp and fix it with
hex socket head bolts as illustrated.
► Fig.15: 1. Hex socket head bolt 2. Handle 3. Upper
clamp 4. Damper 5. Lower clamp 6. Spacer
CAUTION:
Do not remove or shrink the spacer. Doing
so lose the balance of the tool and may cause personal injury.
22 ENGLISH
Always be sure that the tool is
Never start the tool unless it is