Operation; Maintenance Instruction - Max Cordless SuperFramer GS690CH Betriebsanleitung

4 Check operation of the contact arm & trigger if moving
smoothly.
5 Insert the Fuel Cell and the Battery.
6 Hold the Tool with finger-off the trigger, then push the contact
arm against the work-piece. (The tool must not operate.)
7 Check the fan running sound.
8 Hold the Tool with contact arm free from work-piece and pull
the trigger. (The Tool must not operate.)
9 Remove the Fuel Cell and the Battery.
2.

OPERATION

LOADING THE NAILS
Procedure
1 (Fig. 16) Load the nails 1 into the slit in the rear of the Mag-
azine until they completely past the Nail Stopper 2.
2 (Fig.17) Pull the Pusher Holder 3 as far as the rear and of
the magazine and release it gently.
HOW TO DRIVE THE NAILS
The actuation system of the tool is only Full Sequential Actuation.
Procedure
1 Install the Battery and the Fuel Cell.
2 (Fig.18) Press the Contact Arm against where you want to
drive the nails.
The fan motor is activated, the fuel gas is jetted, mixing the
fuel with the air.
3 Firmly pressing the Contact Arm, pull the Trigger. A nail will
be driven into the object by combustion of the fuel.
4 The next nail will not be driven if the Contact Arm is applied
to the object with the Trigger pulled. Release the Trigger
and repeat Step 2 to 3 to drive the next nail.
DRIVING DEPTH ADJUSTMENT DIAL
Adjust the driving depth by twisting the adjustment dial as indicat-
ed below.
Deep
CONTACT TIP (OPTION)
(Fig.19) Attach the Contact Tip 1 on the tip of Contact Arm 2,
when driving nails to a soft material.
CHANGING THE HOOK DIRECTION (Fig.20)
The Hook 1 can be directed in the two directions. Remove the
hexagon socket head bolts 2 with hexagon wrench, change the
direction, and then, put back the bolts to reassemble.
REPLACING THE FUEL CELL
If the Fuel Gas is low, the nails cannot be driven.
1 (Fig. 12) Push up and pull the Fuel Cover 1 to this side to
open it.
2 (Fig. 21) Nip the Metering Valve 2 and remove the used
Fuel Cell 3.
3 Set the new Fuel Cell.
(See Page 3 for the setting method)
REPLACING THE BATTERY
1 If the Battery is low, the red LED of the tool will be turned on.
2 (Fig. 3) Firmly holding the grip, press the latches 2 on both
sides of the Battery 1 to remove it.
3 Install the newly charged Battery into the Housing until it
has clicked.
(See Page 3 for the charging method)
REMOVING JAMMED NAILS
• ALWAYS disconnect the Battery and Fuel Cell.
• Wear gloves when removing jams; do not use bare hands
• Confirm that you have removed all nails from nose of tool
1
2
3

5. MAINTENANCE INSTRUCTION

ARE RESPONSIBLE FOR ENSURING THAT:
1.
2.
3.
4.
5.
1
2
Shallow
3
NOTICE:
• HANDLE THE TOOL WITH CARE
• DO NOT LUBRICATE THE TOOL
• DO NOT FIRE TOOL WITHOUT FASTENERS IN IT.
4
WARNING
before reconnecting to the Battery and Fuel Cell.
Remove the Battery and the Fuel Cell.
Remove the nails remaining in the magazine.
(Fig.22, 23) Remove nails that are jammed inside the Nose
by using a punch or slotted screw driver.
WARNING
Proper maintenance is required to keep tool operating safely.
EMPLOYERS, TOOL OWNERS AND TOOL OPERATORS
tool maintenance instructions are available to appropriate
personnel;
ONLY QUALIFIED PERSONNEL shall repair the tool;
manufacturer's tool maintenance instructions are available
to personnel performing maintenance;
tools that require repair are removed from service and that
tags and physical segregation are used as a means of control.;
all tools in their possession are properly maintained.
INSPECT TOOL AND ALL PARTS DAILY
(1) Tighten all screws, caps and bolts, and check if they
are properly installed.
(2) Keep contact arm moving smoothly.
(3) Check portions that related to the tool controls
(e.g., trigger) are working properly and check for any
air leaks.
CLEAN THE AIR FILTER (Fig.24)
Clean the Air Filter 1 every other day. Open the Air Filter
Cover 2 with a regular screwdriver, and clean it with Com-
pressed air.
INSPECT THE TOOL PERIODICALLY
In order to maintain the performance of the tool, clean and
inspect the tool periodically (Once every year is recom-
mended). To have it inspected, contact MAX authorized
dealers.
Never drop, collide or hit the tool against a hard material. It
may be deformed, cracked or damaged.
Never lubricate the Tool because it will cause problems.
If you repeatedly fire tool without fasteners, the durability of the
tool will be reduced.