Care And Maintenance - Hilti PP10 Bedienungsanleitung

2. Use the laser beam UP / DOWN button to move to
the "input S code" line.
3. Press the SET button to enter the correct mode.
4. The laser beam UP / DOWN button and direction
control button can be used to navigate to the corres-
ponding number. Press the SET button to confirm
the number selected. Press the SET button to con-
firm the code as soon as the four desired digits are
displayed in the "code" area of the display.
5. The display then returns to the previous mode. The
security code can then be activated ("on" by press-
ing the SET button) or deactivated later ("off" by
pressing the SET button again).
The tool then returns to the normal operating mode.
7.18.3 Entering the name of the company
These instructions describe how to enter or change the
name of the company. A maximum of 32 characters (16
characters in 2 rows) can be entered.
1. Press the ON / OFF button and the LOCK button at
the same time.
The set values are shown in the display.
2. Use the laser beam UP / DOWN button to move to
the "change name" line.
3. Press the SET button to enter the correct mode.
4. Use the laser beam UP / DOWN button and direc-
tion control button to navigate to the corresponding
characters / digits. Press the SET button to con-
firm the character selected. Press the SET button
to confirm the entry as soon as the correct name /
designation is displayed.
The tool then returns to the normal operating mode.
7.19 Checking the tool's accuracy 13
1. Set the laser to an inclination of 0.000%.
2. Set up a leveling staff at a distance of 1m and a
second leveling staff at a distance of 60m. Note the
heights at which the laser beam strikes the staffs.

8 Care and maintenance

8.1 Cleaning and drying
1. Blow dust off the lenses.
2. Do not touch the glass with your fingers.
3. Use only a clean, soft cloth for cleaning. If necessary,
moisten the cloth slightly with pure alcohol or a little
water.
NOTE Do not use any other liquids as these may
damage the plastic components.
4. Observe the temperature limits when storing your
equipment. This is particularly important in winter
/ summer if the equipment is kept inside a motor
vehicle (-30°C to +60°C).
8.2 Storage
Remove the tool from its case if it has become wet. The
tool, its carrying case and accessories should be cleaned
All manuals and user guides at all-guides.com
3. Set up an optical level in the middle between the
two leveling staffs and read the heights from both
staffs.
4. Calculate the difference in height indicated by the
optical level and the rotating laser on staffs 1 and
2. If both values are identical, then the laser tool is
correctly adjusted.
NOTE If the differences X1 and X2 are not equal,
please contact your local Hilti Center or Hilti repres-
entative.
7.20 Working with the PPA 20 remote control unit
The "lock" function must be deactivated on the laser tool.
The PPA 20 remote control unit allows you to switch the
laser tool on and off, to activate horizontal alignment and
to select the laser beam mode remotely.
Press the applicable button on the remote control unit to
activate the corresponding function.
7.21 Working in standby mode
To switch the laser tool off, the ON / OFF button on the
laser tool must be pressed.
Only the laser beam is switched off by the ON / OFF
button on the remote control unit. The laser tool remains
in standby mode (the standby LED on the tool blinks
slowly).
When using the remote control unit, point the signal
transmission aperture on the remote control unit toward
the receiving window on the laser tool.
When switching the laser on, press and hold the ON /
OFF button for 2 seconds.
NOTE
If the pipe laser is moved, it can no longer be switched on
by the remote control unit. The message "Error" is shown
on the display of the pipe laser and the laser beam blinks
slowly.
Press the ON / OFF button on the pipe laser and check
that the laser is set up correctly.
and dried (at maximum 40°C / F). Repack the equipment
only once it is completely dry.
Check the accuracy of the equipment before it is used
after a long period of storage or transportation.
Remove the batteries from the tool before storing it for a
long period.
8.3 Transport
Use the Hilti toolbox or packaging of equivalent quality
for transporting or shipping your equipment.
CAUTION
Always remove the batteries before shipping the tool.
8.4 Hilti calibration service
We recommend that the tool is checked by the Hilti cal-
ibration service at regular intervals in order to verify its
en
23