Ec Declaration Of Conformity; General Power Tool Safety Warnings - Makita HP001G Betriebsanleitung

NOTE: T he declared v i b ration total v alue(s) has b een
measured in accordance w ith a standard test method
and ma y b e used for comparing one tool w ith another.
NOTE: T he declared v i b ration total v alue(s) ma y also
b e used in a preliminar y assessment of e x posure.
WARNING:
The vibration emission during
actual use of the po w er tool can differ from the
declared value ( s ) depending on the w ays in w hich
the tool is used especially w hat kind of w orkpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time ) .

EC Declaration of Conformity

For European countries only
T he E C declaration of conformit y is included as Anne x A
to this instruction manual.
SAFETY W ARNINGS
General pow er tool safety w arnings
WARNING:
Read all safety w arnings, instruc-
tions, illustrations and specifications provided
w ith this po w er tool. Failure to follo w all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all w arnings and instruc-
tions for future reference.
T he term " po w er tool " in the w arnings refers to y our
mains - operated (corded) po w er tool or b atter y - operated
(cordless) po w er tool.
Cordless hammer driver drill safety
w arnings
Safety instructions for all operations
1 . W ear ear protectors w hen impact drilling.
E x posure to noise can cause hearing loss.
2 . Use the auxiliary handle ( s ) . Loss of control can
cause personal injury.
Hold the po w er tool by insulated gripping
3 .
surfaces, w hen performing an operation w here
the cutting accessory or fasteners may contact
hidden w iring. C utting accessor y or fasteners
contacting a " li v e " w ire ma y make e x posed metal
parts of the po w er tool " li v e " and could gi v e the
operator an electric shock.
4 . Always be sure you have a firm footing. Be
sure no one is belo w w hen using the tool in
high locations.
5 . Hold the tool firmly.
6 . Keep hands a w ay from rotating parts.
7 . Do not leave the tool running. Operate the tool
only w hen hand-held.
8 . Do not touch the drill bit or the w orkpiece
immediately after operation ; they may be
extremely hot and could burn your skin.
9 . Some material contains chemicals w hich may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follo w material supplier
safety data.
1 0 . If the drill bit cannot be loosened even you
open the ja w s, use pliers to pull it out. In such a
case, pulling out the drill b it b y hand ma y result in
injury by its sharp edge.
Safety instructions w hen using long drill bits
Never operate at higher speed than the max-
1 .
imum speed rating of the drill bit. At higher
speeds, the b it is likel y to b end if allo w ed to rotate
freel y w ithout contacting the w orkpiece, resulting
in personal injury.
2 . Al w ays start drilling at lo w speed and w ith the
bit tip in contact w ith the w orkpiece. At higher
speeds, the b it is likel y to b end if allo w ed to rotate
freel y w ithout contacting the w orkpiece, resulting
in personal injury.
3 . Apply pressure only in direct line w ith the bit
and do not apply excessive pressure. Bits can
b end causing b reakage or loss of control, resulting
in personal injury.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
w ith product ( gained from repeated use ) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follo w the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1 . Before using battery cartridge, read all instruc-
tions and cautionary markings on ( 1 ) battery
charger, ( 2 ) battery, and ( 3 ) product using
battery.
2 . Do not disassemble or tamper the battery
cartridge. It may result in a fire, excessive heat,
or e x plosion.
3 . If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4 . If electrolyte gets into your eyes, rinse them out
w ith clear w ater and seek medical attention right
a w ay. It may result in loss of your eyesight.
5 . Do not short the battery cartridge:
( 1 ) Do not touch the terminals w ith any con-
ductive material.
Avoid storing battery cartridge in a con-
( 2 )
tainer w ith other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to w ater
( 3 )
or rain.
5 ENGLISH