Assembly Preparation - Pit Boss PB3BPGG Montageanleitung

COPYRIGHT NOTICE
Copyright 2020. All right reserved. No part of this manual
may be copied, transmitted, transcribed, stored in a retrieval
system, in any form or by any means without expressed
written permission of,
Dansons
3411 North 5th Avenue, Suite 500, Phoenix, AZ, USA 85013
sales@pitboss-grills.com | service@pitboss-grills.com
www.pitboss-grills.com
Customer Service
Monday through Sunday, 4am - 8pm PST (EN/FR/ES)
Toll-Free: 1-877-303-3134, Fax: 1-877-303-3135
PARTS & SPECS
Part# Description
1 Lid Handle (x1)
2 Cooking Grid A (x2)
3 Cooking Grid B (x1)
4 Lid (x1)
5 Body (x1)
6 Side Shelf (x2)
7 Grease Tray (x1)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact
Customer Service if parts are missing when assembling the unit.
MODEL ASSEMBLED (WxDxH)
1,332 X 604 X 483 MM
PB
PB3BPGG
/ 52.4 X 23.8 X 19.0 IN
2
TABLE OF CONTENTS
Parts & Specs ...................................................................... 2

Assembly Preparation ...................................................... 3

Assembly Instructions
Installing The Lid Handle ............................................................ 3
Mounting The Lid To The Body ................................................. 3
Installing The Side Shelves .........................................................4
Placing The Grease Tray ..............................................................4
Installing The Cooking Grids ......................................................4
3
2
1
4
6
5
WEIGHT COOKING AREA HEAT INPUT
24.0 KG 2,453 CM² /
7.5 KW
/ 52.9 LB 380.2 IN²
Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister pack
after removing from the protective shipping carton. Discard all packaging materials from inside and outside of the grill before
assembly, then review and inspect all parts by referencing the parts list. If any part is missing or damaged, do not attempt to
assemble. Shipping damage is not covered under warranty. Contact your dealer or Pit Boss
through Sunday, 4am - 8pm PST (EN/FR/ES).
service@pitboss-grills.com | Toll-Free: 1-877-303-3134 | Toll-Free Fax: 1-877-303-3135
IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.
IMPORTANT: It is advised to read each step entirely before starting assembly on instructions.
1. INSTALLING THE LID HANDLE
Parts Required:
1 x Lid Handle (#1)
1 x Lid (#4)
Installation:
• First, remove the pre-installed hardware from the Lid Handle.
• Place the Lid Handle into the two holes on the thermometer-side of the
Lid. From the inside of the Lid, fasten the Lid Handle with the previously
removed hardware: place the washer, locking washer, then lock with the
wing-nut. Repeat for other end of Lid Handle.
7
NOTE: Do not over-tighten the wing-nuts. Only a snug fit is necessary.
2. MOUNTING THE LID TO THE BODY
Parts Required:
1 x Lid (#4)
1 x Body (#5)
Installation:
• First, remove the pre-installed Axle Pin and Cotter Pin from the hinge
brackets on the Body.
• Next, lift and carefully place the Lid onto the Body, aligning the hinge
brackets into each other. Anchor both hinge brackets by inserting the
previously removed Axle Pins and securing each with an Cotter Pin.
ASSEMBLY PREPARATION
Customer Service for parts: Monday
®
ASSEMBLY INSTRUCTIONS
1
2
4
1
4
5
3