Operation - Sygonix 1761770 Bedienungsanleitung

c) Registering a Receiver for the Temperature Controller
The temperature controller can control a receiver of the RS2W radio switch system
(e.g. a radio switch socket that is part of the system). Other receivers cannot be
used.
Follow the operating instructions of the receiver of the RS2W radio switch system
that will be used prior to the registration procedure.
A dimmer of the RS2W radio switch system cannot be used.
During the registration process, maintain a 20 - 30 cm minimum distance between
the temperature controller and the receiver. Failing to do this may result in a registra-
tion failure.
• If the receiver is switched on, switch it off for the moment.
The receiver (e.g. a radio switch socket) must be switched off (LED in the button is
off); otherwise, registration cannot be done.
• Start the registration procedure at the temperature controller.
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears on the left in the
display.
Hold the "+/ON" button pressed for 2 seconds until the two arrows in the "
flash alternately. Then release the button.
The temperature controller is now ready to register the receiver.
• Hold the button on the receiver pressed (approx. 3 seconds) until the two arrows in the "
" symbol on the temperature controller stop flashing.
• The receiver switches on to indicate the end of the registration process.
Only one receiver can be registered at the temperature controller (a receiver of the
RS2W radio switch system, but not a dimmer).
If you start a new registration procedure and register another receiver of the RS2W
radio switch system, the receiver registered previously will be deleted/overwritten.
d) Deleting a Registered Receiver
If the receiver is registered at the temperature controller, proceed as follows:
• Start the registration procedure at the temperature controller.
Repeatedly press the "FUNC" button briefly until "CANCEL" appears on the left in the display.
Hold the "+/ON" button pressed for 2 seconds until the two arrows in the "
flash alternately. Then release the button.
• Hold the "+/ON" button pressed again for 2 seconds and the registered receiver will be
deleted; the right part of the "

Operation

a) Selecting Heating or Cooling Mode
In heating mode, the receiver is activated when the measured temperature is below
the set target temperature. This operating mode can be used in conjunction with a
heater.
In cooling mode, the receiver is activated when the measured temperature is above
the set target temperature. This operating mode can be used in conjunction with a
cooling unit or fan.
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears in the display.
• Hold the "+/ON" and "-/OFF" buttons pressed at the same time to toggle between the heat-
ing and cooling mode.
Depending on the mode selected, a corresponding symbol appears in the top left of the
display:
" " Heating mode
" " Cooling mode
b) Switching the Consumer On/Off Manually
At the receiver
Follow the operating instructions of the receiver of the RS2W radio switch system.
At the button on the temperature controller
• Repeatedly press the "FUNC" button briefly until "CANCEL" appears in the display.
• The registered receiver can be switched on with the "+/ON" button and switched off with
the "-/OFF" button.
" symbol and the two arrows disappear.
c) Selecting and Setting the Programme
• Repeatedly press the "FUNC" button briefly until "AUTO" appears in the display.
• Select one of the 8 programmes "PROG1" to "PROG8" with the "+/ON" or "-/OFF" button.
• Hold the "FUNC" button pressed (approx. 3 seconds) until the temperature flashes at the
left in the display.
• Set the temperature with the "+/ON" or "-/OFF" buttons. For quick adjustment, press and
hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the weekdays will flash.
• Set the weekday or the period using the "+/ON" or "-/OFF" buttons.
You can set:
"MO" = Monday
"TU" = Tuesday
"WE" = Wednesday
"TH" = Thursday
"FR" = Friday
"SA" = Saturday
" symbol
"SU" = Sunday
"MO TU WE TH FR" = Monday to Friday
"MO TU WE TH FR SA SU" = Monday to Sunday
• Briefly press the "FUNC" button and the hours of the starting time will flash.
You can now enter a time period during which the set temperature should be maintained
(e.g. from 8am to 5pm).
Keep in mind that the set time periods must not overlap (e.g. if you would set pro-
gramme 1 from 8 am to 5 pm and programme 2 from 9 am to 3 pm). Otherwise,
some switching times or temperatures may not be activated as a result.
If a temperature is to be maintained for the entire day, set the same time for starting
and ending time.
• Set the hours of the starting time with the "+/ON" or "-/OFF" buttons. For quick adjustment,
press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the minutes of the starting time will flash.
• Set the minutes of the starting time with the "+/ON" or "-/OFF" buttons. For quick adjust-
" symbol
ment, press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the hours of the ending time will flash.
• Set the hours of the ending time with the "+/ON" or "-/OFF" buttons. For quick adjustment,
press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and the minutes of the ending time will flash.
• Set the minutes of the ending time with the "+/ON" or "-/OFF" buttons. For quick adjustment,
press and hold down the corresponding button for longer.
• Briefly press the "FUNC" button to confirm and to exit the setting mode.
d) Manual Temperature Pre-selection
• Repeatedly press the "FUNC" button briefly until "MANU" appears in the display.
• Hold the "FUNC" button pressed (approx. 3 seconds) until the temperature flashes on the
left in the display.
• Select the desired temperature with the "+/ON" or "-/OFF" button. For quick adjustment,
press and hold down the corresponding button for longer.
• Press the "FUNC" button briefly to confirm.
Manual temperature pre-selection remains activated for the following 24 hours and
then changes back to automatic operation.
e) Selecting the Operating Mode ("AUTO", "MANU", "CANCEL")
If the temperature controller is not in a setting mode, you can select the operating mode by
briefly pressing the "FUNC" button.
Operating mode "AUTO"
The temperature controller maintains the temperature automatically according to the settings
made for times/weekdays in the 8 programmes "PROG1" to "PROG8".
Operating mode "MANU"
The temperature controller maintains the temperature after activation of this operating mode for
a duration of 24 hours and then changes back to automatic operation.
Operating mode "CANCEL"
The temperature controller is deactivated; a switching process is not executed.