Werbung
Verfügbare Sprachen
Verfügbare Sprachen
6 Product overview
1 Display
2 On/off button
- Short press to switch the device on
or off.
3 Settings button
- Short press to switch between
manual and automatic mode.
- Press and hold (approx. 3
seconds) to set the time and turn the
timer on/off.
4 Thermostat-controlled power
outlet
5 Cable with temperature sensor
6 LED
- Indicates whether the socket is
switched on or off.
7 Decrease button
- Short press to decrease the value.
- Press and hold for about 3 seconds
to unlock.
8 Increase button
- Short press to increase the value.
- Press and hold for 3 seconds to access the advanced settings.
9 Confirm button
- Press and hold for 3 seconds to enter programming mode.
6.1 Explanation of the display symbols
1
2
3
4
5
6
1 Day of the week
2 Current time
3 Temperature setting (set temperature)
4 Manual mode (Manual temperature control)
5 Automatic mode (preset program is running)
Short press the Settings button (
6 6 programmable periods
(morning, work, lunch (arrive), lunch (leave), after work, night).
7 Room temperature (actual temperature)
8 Heating mode
The symbol appears on the display when the socket is turned on.
Frost protection
The symbol appears on the display when the socket is switched on.
The mode can be changed in the advanced settings.
9 Cool mode
The symbol appears on the display when the power outlet is turned on.
The mode can be changed in the advanced settings.
10 Window open detection
The mode can be changed in the advanced settings.
11 Button lock enabled: To unlock, press the
7 Getting started/operation
7.1 Getting started
Follow the safety instructions and the other information in this operating manual.
Follow the operating instructions for the devices connected by you, and observe
the respective minimum and maximum load in the "Technical Data" section.
If the warning sticker is not attached to the product, attach the sticker for
your language to the product.
Caution! Adapters must not be plugged into each other.
1
2
3
4
5
) to switch between manual and automatic mode.
button for about 3 seconds.
Devices with electronic power adapters (e.g. TVs or high-voltage LED light bulbs) do not
have resistive loads. They can generate inrush currents of over 100 A. Using these types
6
of loads can cause the relay to wear out prematurely.
Place the remote temperature sensor in the desired location or secure it to the measuring
location, e.g. with a cable tie.
The temperature sensor is not designed for prolonged use in liquids!
7
8
9
Plug the product in a 230 V/AC mains socket with protective earth contacts and connect the
load (max. 16 A / 3680 W) to the socket on the product.
7.2 Setting the time
Hold down the
access the settings.
To select the time setting, press the
ton repeatedly until the
Press the
button to confirm your entry.
The minute setting will start to flash.
Set the minute setting with the
button. The hour setting will start to flash.
Set the hour setting with the
button. The day of the week setting will start to flash.
Set the day of the week using the
button. The display will return to the settings.
After approx. 5 seconds, the display will automatically switch back to the main overview.
The time was set successfully.
7.3 Setting the operating time (when the thermostat is active)
These settings allow you to determine the time at which the thermostat operates. Outside this
time, the thermostat is inactive (the display and the thermostat function are switched off).
7
Hold down the
To set the operating time, press the
8
Press the
9
Æ
The minute setting will start to flash.
Æ
Set the minute setting with the
10
button. The hour setting will start to flash.
Set the hour setting with the
11
button. The display will return to the settings.
After approx. 5 seconds, the display will automatically switch back to the main overview.
The operating time was set successfully.
7.4 Periods with different temperatures
With these settings, you can set different temperatures for different times of the day. Separate
settings can be configured for working days and weekends.
Hold down the
Monday to Friday
The
symbol and the temperature
display will start to flash.
Use the
or
sired temperature. Press the
to confirm your entry.
The hour setting will start to flash. Set
the hour setting with the
tons, and then confirm your entry with
the
button.
The minute setting will start to flash. Set the minute setting with the
then confirm your entry with the
Proceed in the same way to set the other time periods. These settings apply from Monday
to Friday.
Saturday and Sunday
Once you have programmed all time pe-
riods and temperatures for Monday to
Friday, the
the display.
For the weekends, you can configure a
day program from morning to evening.
Proceed in the same way for the
temperature and time settings as for
weekdays.
After approx. 5 seconds, the display will automatically switch back to the main overview.
The time periods were set successfully.
button for 3 seconds to
but-
symbol flashes.
or
buttons, and then confirm your entry with the
or
buttons, and then confirm your entry with the
or
buttons, and then confirm your entry with the
button for 3 seconds to access the settings.
button repeatedly until the „ON" symbol flashes.
button to confirm your entry.
or
buttons, and then confirm your entry with the
or
buttons, and then confirm your entry with the
button for 3 seconds to access the settings.
buttons to set the de-
button
or
but-
button.
symbol will appear on
or
buttons, and
Werbung
