Technical Data; Before Starting The Machine; General Information - Scheppach SD1600V Originalbetriebsanweisung

GB
• Never leave the work area without having already
switched the saw off. Wait until the saw stops mov-
ing completely.
• Do not position, join, or construct any parts on the
work table while the saw is running.
• Only switch the saw on after you have removed any
remaining material and tools from the work table.
Leave only the workpiece to be machined and any
aids (e.g. wedges) on the work table.
• Always wear safety goggles!
• Keep your fingers at a safe distance from the saw
blade.
• Carefully guide the workpiece and keep it steady
at all times.
• Never leave the work area without having already
switched the saw off.
• Do not let your familiarity with the saw allow you
to be careless. Carelessness can lead to severe
injuries within a fraction of a second.
Work safely
• When transporting the power tool, lift the it on the
machine base.
• Never use protective devices for handling or trans-
port.
• During transport, ensure that the bottom of the saw
blade is covered, for example, by the protective de-
vice.
• Prior to commissioning, protective devices and
safety devices must be installed in accordance with
good engineering practice.
• Working position: always laterally with respect to
the saw blade.
Do not lose this safety information.

6. Technical data

Mains voltage: 220-240 V ~/50 Hz
Power input: 120 W
Operating mode: S6 30%
Power input: 80 W
Operating mode: S1
Stroke rate: 500 - 1,700 rpm
Protection type: IP 20
Stroke: 12 mm
Base area: 630 x 295 mm
Tilting range of table: 0° to 45° to the left
Table size: 415 x 255 mm
Length of saw blade approx.:
Reach: 406 mm
Max. cutting height at 90°: 50 mm
Max. cutting height at 45°: 22 mm
Weight: 12,7 kg
Operating mode S6 30%:
Continuous operation with idling (cycle time 10 min-
utes). To ensure that the motor does not become ex-
cessively hot, it may only be operated for 30% of the
cycle at the specified rating and must then be allowed
to idle for 70% of the cycle.
22 / 44 22 / 44
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
134 mm
Noise emission values
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 61029.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Sound pressure level L : 66.9 dB(A)
pA
Uncertainty K : 3 dB(A)
pA
Sound power level L : 79.9 dB(A)
WA
Uncertainty K : 3 dB(A)
WA
The quoted values are emission values and not nec-
essarily reliable workplace values. Although there is
a correlation between emission and immission levels
it is impossible to draw any certain conclusions as
to the need for additional precautions. Factors with
a potential influence on the actual immission level
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighboring op-
erations.
Reliable workplace values may also vary from coun-
try to country. With this information the user should
at least be able to make a better assessment of the
dangers and risks involved.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.

7. Before starting the machine

Important.
Always pull out the power plug before making adjust-
ments to the equipment.

7.1 General information

• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
equipment's moving parts run smoothly.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equipment to the power supply.
• Only ever connect the equipment to a properly in-
stalled shock-proof socket which is protected by a
10A fuse as a minimum.