Scheppach SD1600V Originalbetriebsanweisung Seite 23

7.2 Installing the fretsaw on a workbench (Fig. 3,
4)
The unit may only be installed by a professional.
Required for installing (not provided):
• M6 hex screw (4x)
• M6 hex nut (8x)
• Washer, Ø 7 mm (4x)
• Flat gasket, Ø 7 mm (4x)
• Rubber base: 410 x 255 x 13 mm
The length of the screws to be used varies, depend-
ing on the thickness of the table top.
• Install the fretsaw on a work table made from solid
wood. This will avoid excessive noise caused by
vibrations.
• Mark the drill holes. Use the fretsaw as a template
for this purpose.
• Drill 4 holes with a diameter of 9 mm into the work
table and the rubber base.
• Screw the fretsaw to the table using the mounting
points (Fig. 3/12, Item 16) and in the following se-
quence (Fig. 4):
A) Fretsaw
B) Rubber base
C) Work table
D) Flat gasket
E) Washer
F) Hex nut
G) Hex nut
H) Hex screw
• Tighten the hex nut (F) and secure it with a second
hex nut (G).
7.3 Assembly
Important! Always pull out the power plug before car-
rying out any maintenance or conversion work on the
fretsaw.
7.3.1 Mounting the saw blade guard and the saw-
dust blower facility (Fig. 6/7/8)
• Attention: Prior to the installation of the retaining
device (18), the pre-assembled saw blade (17)
must be dismantled as described in articel 7.3.2.
• Attach the retaining device (18) to the bracket (29),
as shown in the figure. First, the bracket has to be
attached to the machine using the knurled screw
(3).
• Secure the saw blade guard (5) with the nut and
bolt.
• Fold down the saw blade guard (5) above the hold-
down clamp (18).
• Mount the blow-off device (1) as shown in Figure
8. The blow-off device (1) is designed to blow away
ejected material on the topside of the workpiece
during the sawing process . This means that the
cut marks remain visible.
• Adjust the flexible blow-off device (1) so that this
points in the direction of the saw blade.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58  www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
7.3.2 Changing the saw blade (Fig. 1/9/10)
Important
To avoid injuries attributed to inadvertent startup: Al-
ways move the switch to the "0" position and pull the
power plug out of the socket outlet before removing or
changing the saw blade.
A. Flat saw-blades Fig. Fig. 9+9.1+9.2+9.3+9.4
Use the adapter (19/23) with flat saw-blades.
The distance results by the setting gauge (32).
The saw-blade is fixed with Allen screws.
Removing the saw blade without pins (optional)
• To remove the saw blade (17), lift the table insert
(26) upwards.
• First release the tension by lifting the clamping le-
ver (9) upwards. If required, further reduce the ten-
sion by turning it anti-clockwise.
• Slightly push down the outrigger (10).
• Then remove the sawblade by pulling it forward out
of the supports and through the access perfora-
tion in the table.
Inserting the saw blade without pins (optional)
The teeth of the saw blade must always point down-
wards.
• Put the saw-blade with the two adapters (19/23)
into the lower support, the other end into the up-
per support.
• Slightly push down the outrigger (10).
• Tighten the saw blade (17) with the clamping lever
(9) by pressing it down again. Check the tension
of the saw blade (17). If the tension is insufficient,
it can be increased by turning the lever clockwise.
First release the clamping lever (9).
• Put the table insert (26) back.
B. Saw-blade with pins Fig. 10+10.1+10.2+10.3
Removing the saw blade with pins
• To remove the saw blade (17), lift the table insert
(26) upwards.
• First release the tension by lifting the clamping le-
ver (9) upwards. If required, further reduce the ten-
sion by turning it anti-clockwise.
• Slightly push down the outrigger (10).
• Pull the saw blade from the upper and lower saw
blade mounting (24/25)
Inserting the saw blade with pins
The teeth of the saw blade must always point down-
wards.
• Push one end of the saw blade (17) through the
hole in the table, and guide the pins of the saw
blade (17) into the corresponding slots in the upper
and lower saw blade mounting (24/25).
• First insert the saw blade (17), in the lower blade
holder (25).
• Slightly push down the outrigger (10).
• Check the position of the saw blade pins in the saw
blade mountings (24/25).
GB
23 / 44 23 / 44