Layout And Items Supplied - EINHELL TS 115/125 Originalbetriebsanleitung

14. Do not use the cutting stand with high-perfor-
mance electric tools that are not suitable for
the accessory device.
15. Use only cutting-off wheels for metal.
16. Make sure that the cutting-off wheel moves
vertically to the base plate.
17. Secure the workpiece carefully. It has to be
securely clamped in a straight position in
order to prevent it from moving and skewing
while the cut is being made.
18. Do not try to cut workpieces which are obvi-
ously too big for the cutting stand.
19. Make sure that the cutting-off wheel stops
completely before you remove the workpiece,
clamp in a new workpiece, or adjust the ang-
le.
20. Never reach behind or near the cutting-off
wheel.
21. Never leave an electric tool unattended when
it is running. Always switch off your electric
tool before leaving it.
22. Always pull out the power plug when not in
use, before carrying out any maintenance
work and before changing the tool.
23. Avoid unintentional starting. Make sure that
the switch is OFF when inserting the plug in
the socket-outlet.
24. Never use circular saw blades or ceramic
wheels.
25. Before starting, make sure that the machine is
fastened in the holder securely and properly.
26. Never use your hands or any other objects to
stop the wheel.
27. Do not overload your tool; allow the wheel to
work without applying any pressure.
28. Check to see if all parts are mounted. In this
connection, please read the instructions and
particularly the safety information. Never use
the machine if it is not fully assembled.
29. Use the accessory parts and electric tool for
their intended purpose only.
30. Check to see if the accessory parts are not
damaged. Also make sure that moving parts,
clamping devices and safety guards are wor-
king correctly.
31. Be alert at all times. Concentrate on what you
are doing. Use common sense when working.
Never use the electric tool when you are dis-
tracted.
32. The cutting stand is designed for cutting fer-
rous metals. Do not try to cut wood, brick or
other unsuitable materials.
33. Do not stand in the cutting direction after a
new cutting-off wheel has been fi tted. Allow
the machine to run for approximately one
Anl_TS_115_125_SPK9.indb 16 Anl_TS_115_125_SPK9.indb 16
GB
minute before you begin with the cutting. If the
cutting-off wheel has an invisible fracture or
defect, it will burst in less than one minute.
34. Keep your electric tools in a safe place. When
equipment is not being used it should be kept
in a dry, closed place out of children's reach.
35. Wear suitable work clothes. Do not wear loo-
se clothing or jewelry as they may get caught
in moving parts. Non-slip shoes are recom-
mended. Wear a hair net if you have long hair.
36. Always remove keys and wrenches after use.
Before switching on, make sure that all keys
and wrenches have been removed from the
tool.

2. Layout and items supplied

2.1 Layout (Fig. 1-4)
1. Base plate
2. Fastening screws for angle grinder
3. Clamping device for workpiece
4. Swing arm
5. Handle
6. Cable clip
7. Holder for angle grinder
8. Adjusting screws for angle grinder
9. Spark guard
Important: There is no angle grinder supplied
with the cutting stand!
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
- 16 -
17.02.2021 08:33:11 17.02.2021 08:33:11