Scheppach DB2000 Original Bedienungsanleitung Seite 18

f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for opera-
tions different from those intended could result in
a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained..
Appliance-Specific Safety Instructions for Ham-
mers
• Wear ear protectors. Exposure to noise can cause
hearing loss.
• Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
• Use suitable detectors to determine if utility lines
are hidden in the work area or call the local util-
ity company for assistance. Contact with elec-
tric lines can lead to fire and electric shock.
Damaging a gas line can lead to explosion. Pene-
trating a water line causes property damage or may
cause an electric shock.
• When working with the machine, always hold it
firmly with both hands and provide for a secure
stance. The power tool is guided more secure with
both hands.
• Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure
than by hand.
• Wear a dust mask.
Additional Safety and Working Instructions
Warning
• Do not overreach. Keep proper footing and balance
at all times.
• Use protective equipment. Always wear safety
glasses when working with the machine. The use of
protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear
and ear defenders.
• The dust produced when using this tool may be
harmful to health. Do not inhale the dust. Use a
dust absorption system and wear a suitable dust
protection mask. Remove deposited dust thorough-
ly, e.g. with a vacuum cleaner.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Always keep the connection cable from the working
area of the device. Always guide the cable back-
wards, away from the device!
• Do not machine any materials that present a dan-
ger to health (e.g. asbestos).
• When working in walls ceiling, or floor, take care to
avoid electric cables and gas or waterpipes.
• Please turn the device immediately off when the
tool used gets blocked! Do not turn the device
on again when the tool is still blocked. This could
cause bounce back with a high reaction moment.
Determine and remove the cause of the blocking
of the tool used while respecting the safety instruc-
tions.
• The possible causes may be:
- it is tilted in the workpiece to be machined
- it has pierced through the material to be ma-
chined
- the power tool is overloaded
• Do not reach into the machine while it is running.
• Chips and splinters must not be removed while the
machine is running.
m WARNING! Danger of burns
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
m WARNING! This electric tool generates an electro-
magnetic field during operation. This field can impair
active or passive medical implants under certain con-
ditions. In order to prevent the risk of serious or dead-
ly injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
Residual risks
Even when this electric tool is used properly, re-
sidual risks still remain.
The following hazards may arise in connection
with the design and construction of this electric
tool:
• Lung damage if suitable dust protection mask is not
worn.
• Hearing damage if suitable hearing protection is
not worn.
• Damage to health resulting from hand/arm vibra-
tion if the device is used over an extended period
of time or if it is not properly operated and main-
tained..