Specifications; Functional Description - Makita TW0350 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Socket
3 Anvil
4 O-ring
5 Pin

SPECIFICATIONS

Model
Capacities
Standard bolt .............................................. M12 – M22
High tensile bolt .......................................... M12 – M16
Square drive ...................................................... 12.7 mm
–1
No load speed (min ) ............................................ 2,000
Impacts per minute ................................................. 2,000
Max. fastening torque ........................................ 350 N•m
Overall length ..................................................... 283 mm
Net weight .............................................................. 3.0 kg
Safety class ................................................................ /II
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for fastening bolts and nuts.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
IMPACT WRENCH SAFETY WARNINGS
1. Hold power tool by insulated gripping surfaces,
when performing an operation where the fas-
tener may contact hidden wiring or its own cord.
Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Wear ear protectors.
3. Check the socket carefully for wear, cracks or
damage before installation.
4. Hold the tool firmly.
5. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4
Explanation of general view
6 Standard bolt
7 Fastening torque
8 Fastening time
9 High tensile bolt
10 Limit mark
6.
TW0350
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
ENE036-1
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
ENF002-2
"OFF" position when released.
• Change the direction of rotation only after the tool
comes to a complete stop. Changing it before the tool
stops may damage the tool.
The switch is reversible, providing either clockwise or
counterclockwise rotation. To start the tool, simply pull
the lower part of the switch trigger for clockwise, the
GEA010-1
upper part for counterclockwise. Release the switch trig-
ger to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Selecting correct socket
GEB009-6
Always use the correct size socket for bolts and nuts. An
incorrect size socket will result in inaccurate and incon-
sistent fastening torque and/or damage to the bolt or nut.
Installing or removing socket
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the socket.
For socket without O-ring and pin (Fig. 2)
To install the socket, push it onto the anvil of the tool until
it locks into place.
To remove the socket, simply pull it off.
11 Brush holder cap
12 Screwdriver
The proper fastening torque may differ depend-
ing upon the kind or size of the bolt. Check the
torque with a torque wrench.