Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
d) The menu for entering the network
name will appear:
SSID
0123456789._ ,
abcdefghijklmn
opqrstuvwxyzABC
DEFGHIJKLMNOPQR
Fig. 16
Enter the network name and con-
firm (operation of the input menu:
Entering the network key under
☞
step 7)
e) In the following two menus, set
the encryption method used by the
router
7) If the network access is encrypted, a menu
for entering the network key will appear
(if the WPS menu shown below appears,
continue as described there):
Key:
0123456789._ ,
BKSP
abcdef g hijklmn
OK
opqrstuvwxyzABC
DEFGHIJKLMNOPQR
CANCEL
Turn the knob CONTROL SELECT to select
the characters and the three fields and
then press the knob to confirm (with the
remote control: use the arrow keys to
select the characters / fields and press
ENTER to confirm)
= to delete last character
BKSP
= to confirm the key
OK
= to return to the previous menu
CANCEL
Note: To select the fields
BKSP
turn the knob backwards beyond the first digit
or forwards beyond the final special character
With the remote control: at the beginning of a
line, press
or, at the end of a line, press
then use
or
to select the field desired
The network connection will be estab-
lished once the network key has been
confirmed
If the router supports WPS (Wi-Fi Protected
Setup), the WPS menu will appear instead
of the menu for the network key:
WPS Menu
Push Button
PIN
Skip WPS
WPS allows you to integrate a unit into an
encrypted wireless LAN network without
entering the network key Two methods
are available:
Method 1: If the router supports WPS
via PBC (Push Button Configuration), this
method should be used
selected Press the knob CONTROL SELECT
to confirm The following menu will ap-
pear:
WPS Setup
Push WPS
button at the
other end
Press SELECT to
continue
First press the WPS button at the router,
then press the knob CONTROL SELECT at
WAP-202 The connection will be estab-
lished For detailed information on how
to proceed, also observe the instructions
BKSP
in the manual/user interface of the router
OK
Method 2: If the router supports WPS via
CANCEL
PIN entry, this method can be used as an
alternative to the PBC method Select
and confirm
will appear, showing an 8-digit PIN Enter
this PIN at the router and press the knob
CONTROL SELECT at WAP-202 Then start
the connection at the router For detailed
information on how to proceed, also ob-
serve the instructions in the manual / user
interface of the router
If WPS is not to be used, select and con-
firm
Skip WPS
network key as described above
8) While the network connection is being
established, various messages will be
shown:
Please wait ...
Fig. 17
Once the network connection has been
established, the message
appear, followed by the message
Setup wizard
Press SELECT to exit
Press the knob CONTROL SELECT to exit
,
and
,
the setup wizard: the main menu will
OK
CANCEL
appear Use the main menu or the but-
ton MODE to select the operating mode
desired (chapter 4)
;
If the wizard fails to establish a connection
to the router (message
first check the settings of your router (e g
SSID, WPS method used or network key)
You may be able to improve wireless LAN
reception by reducing the distance between
the unit and the router or by realigning the
wireless LAN antenna
If the network connection is wrong, reset
>
the network settings (in the menu "System
>
settings"
>
settin g s
tion again
Fig. 18
Push Button
is
Fig. 19
: The menu
PIN
WPS Setup
Then enter and confirm the
Connected
Setup wizard
completed
Fig. 20
Failed to connect
Network
Clear network
) and then establish the connec-
3.4 Further settings via the menu
"System settings"
The settings that can be made via the setup
wizard are also available via the corre-
sponding menu items of the menu "System
settings" This menu also provides additional
setting and display options An overview of
the options provided by the menu "System
settings" can be found in fig 27
The menu can be called up from any oper-
ating mode: Press the button MENU,
turn the knob CONTROL SELECT to select
System settin g s
and then press the knob
to confirm The menu "System settings" will
be shown:
System settin g s
Equaliser
Network
Time/Date
Lan g ua g e
Factory reset
For operation of the menu, the following gen-
erally applies: To select a menu item or set-
ting, turn the knob; to call up a menu item or
to confirm a setting, press the knob To return
to the previous menu level, press the button
will
BACK or, when in a menu as shown in fig 17,
select the field "CANCEL" and confirm
3.4.1 Selecting the menu language
Lan g ua g e
En g lish
Danish
Dutch
Finnish
French
Select the desired language in this menu The
following languages are available: English,
Danish, Dutch, Finnish, French, German, Ital-
ian, Norwegian, Polish, Portuguese, Spanish,
),
Swedish, Turkish
Once the selection has been confirmed,
the menu "System settings" will appear in
the language selected
3.4.2 Display backlight
Backli g ht
Timeout
On level
Dim level
1) Use
On level
to set the brightness of the
display backlight when the unit has been
switched on Three settings are available:
Hi g h
,
Medium
and
2) Use
Dim level
to set the brightness of
the display backlight when the unit is
in the standby mode Three settings are
available:
,
Medium
Low
backlight)
3) Use
to set the time the unit must
Timeout
be in standby mode until the display back-
light changes to the brightness setting
of the standby mode Select the desired
time or the setting
change to the brightness setting of the
standby mode)
>
>
>
>
Fig. 21
*
Fig. 22
>
>
>
Fig. 23
Low
and
(no display
Off
(the display will not
On
19
Werbung
Inhaltsverzeichnis
