2 Ir Remote Control; 2 1 Function Overview; 2 2 Inserting / Replacing The Battery; 3 Initial Switch-On And Making Settings With The Setup Wizard - Monacor WAP-202 Bedienungsanleitung

3.2 IR remote control

The remote control requires a 3 V button cell
of the type CR 2025 (not supplied with the
remote control) If there is a protective film
on the battery holder, remove the film and
then insert the battery ( chapter 3 2 2)
☞
The remote control is now ready for oper-
ation When you press a button on the remote
control, always point the remote control at
the IR sensor ( fig 2) Make sure that there
☞
are no obstacles between the sensor and the
remote control
If the remote control is not used for a
longer time, remove the battery as a precau-
tion so that the remote control will not be
damaged in case the battery should leak
3.2.1 Function overview
Most of the functions are available via the
remote control They are not always addition-
ally described in the following chapters and
are therefore listed in the following overview:
Button Function
to switch on  go to the standby mode
1 – 5 to call up saved stations 1 ... 5
to call up saved stations 6 ... 10:
SHIFT
press SHIFT, then button 1 ... 5
FM, DAB and Internet radio:
to save stations: keep the button pressed for
PRESET a while to call up the storage menu, select
the storage location by means of  or 
and then save with ENTER.
to set the time of the sleep timer function;
SLEEP
to set the alarm interval
to call up / exit the menu "Alarms";
when the alarm sounds: to stop the alarm;
ALARM
in standby mode: to switch alarms 1 and 2
on / off ( ☞ chapter 4.8, item 6)
INTERNET RADIO
1 2 3 PRESET
SHIFT SLEEP
4 5
MENU INFO ALARM
ENTER ENTER MODE
REPEAT SHUFFLE
PLAY/STOP VOLUME MUTE
Internet Radio
HIT Radio­ABC
Jonny White ­ I can't
forget you
POWER
➁
Button Function
to select the operating mode:
Internet radio
MODE
 DAB radio

Bluetooth Audio
to call up the menu;
MENU to return to the highest menu level;
to exit the menu
 / to select a menu line
/ to select settings in the menu
 to return to the previous menu level
to call up a menu item or
ENTER
to confirm a setting
Internet radio, FM / RDS or DAB:
to show additional information
INFO
music player:
to show additional title information
music player:
REPEAT to replay the titles continuously
( ☞ chapter 4.4.4)
music player:
SHUFFLE to replay the titles in random order
( chapter 4.4.4)
☞
PLAY/ music player or Bluetooth*:
STOP to pause / continue the replay
VOLUME
to adjust the volume
+ −
MUTE to mute / unmute the sound
FM:
to start the scan (keep the button pressed
until the scan starts)
I  /  I
music player or Bluetooth*:
to go to the previous / next title
music player or Bluetooth*:
 / 
fast reverse / fast forward
* function available depending on the Bluetooth source used
Fig. 3 Functions of the remote control
19:31
WAP-202
USB AUX
INPUT
3.2.2 Inserting / Replacing the battery
1) Push the latch of the battery support to
 Music player
 FM radio

Aux in
2) When replacing the battery, remove the
3) Insert the new battery in the support, posi-
3.3 Initial switch-on and making
1) Use the switch POWER to switch on the
IR sensor for the
remote control
CONTROL SELECT
MODE PRESET REPEAT
SELECT BACK MENU SHUFFLE
ENTER
the right (first arrow in fig 4) and pull out
the support (second arrow)
1. 2.
Fig. 4 Battery support
discharged battery
tive pole facing upwards Push the support
back into the remote control
Never put batteries in the house-
hold waste Always dispose of the
batteries in accordance with local
regulations
settings with the setup wizard
unit The message WELCOME
graph will be shown on the display
Then the setup wizard will appear:
Setup wizard
Start now?
YES NO
Notes:
1 The unit is in the stand-by mode if only the
date and the time are shown on the display
after the switch POWER was used In this case,
switch on the unit with the button STANDBY
(or on the remote control)
2 If
Network settin g s
Please wait
Connectin g .
appears on the display, press the button
MENU, turn the knob CONTROL SELECT to
select the line
System settin g s
knob to call up the menu "System settings"
In the menu "System settings", turn the knob
to select the line
Setup wizard
knob to call up the setup wizard Then con-
tinue with step 2
3 Instead of English, a different menu language
can be set (see chapter 3 4 1)
4 The wizard can be called up any time via the
menu "System settings"
MAIN VOLUME
INFO ALARM SLEEP STANDBY
MUTE PREV NEXT PLAY/II
and a bar
Fig. 5
and press the
and press the
17