Changing The Lamp; Faults - What To Do If; Customer Service; Installation - KKT KOLBE DELTA Bedienungsanleitung

English
Each time you change or wash a grease filter or
carbon filter, after removal clean all exposed lower
parts of the hood with a mild grease solvent.
For the daily cleaning of the outer pats of the hood
use a soft cloth moistened with alcohol or a mild
liquid cleaner. Never use an abrasive cleaner.
There is a risk of fire if the instructions for
cleaning the hood and the changing or cleaning of
the filters are not complied with.
8. Changing the lamps
When changing a lamp, make sure that the
new lamp does not have a higher wattage than that
of the original.
9. Fault – what to do if ...
The motor fails to function:
Is the plug properly inserted in the socket?
Is there a power supply failure?
Has a fuse blown?
The hood capacity is insufficient / operating
noise has increased:
Is the size of the exhaust air pipeline sufficient?
Is the exhaust air duct blocked?
The cross section of the air pipeline (from the
hood to the wall box incl.) should be 150 mm.
A smaller air pipeline cross-section can possibly
impair the motor power.
The air flow can be obstructed if the wall box is
fitted with a fly mesh.
If this is the case remove the fly mesh.
If the cover plate of the wall box has fixed, very
inclined louvres, you should remove the plate to
check whether this solves the problem.
Mount a cover plate with movable louvres in the
wall box, as this will least obstruct the air flow.
Is / are the filter(s) clean?
Was / were the carbon filter(s) installed more
than six months ago?
Then this/these should be changed.
Is the air taken from the kitchen being replaced
by sufficient fresh air, so that no partial vacuum is
being produced in the room?
The lighting fails to function:
Does the lamp need changing?
Has the lamp been properly fitted and seated in
the holder up to the stop?
Is the fuse blown or has the circuit breaker
tripped out?
fi90520ATL
Operating instructions / users manual Cooker Hoods
If all the above checks fail to remedy the
fault, it is possible you have a more serious
problem.
In no circumstances
electronic/electrical compon ents in the appliance.
Contact your Customer Service.

10. Customer Service

For technical queries concerning your appliance
please contact the customer service office of your
dealer.
The type and rating plate is located inside the
appliance (remove the grease filter)

11. Installation

On installation, the minimum distance between the
hob and the hood must be exactly complied with
(see chapter 11.1 "Installation data") and follow the
numbering of the steps and the additional
instructions. Execution with air exhausted outdoors
(A- see also the installation data). The vapours are
extracted via an air exhaust hose fixed to the
connector ring.
The diameter of the exhaust air hose must conform
to that of the connector ring. If a smoke non-return
valve is used or is planned, check whether it can
open and close freely after the installation of the
exhaust air hose. The extractor hood can be
equipped with one (top) or two (top and back)
extractor openings.
The hood is normally initially fitted out for use of the
top extractor opening, as an extractor hood .
Openings not required are fitted with a plastic cover.
This plastic cover can be easily removed by turning
counterclockwise and optionally fitted to another
opening which is not required.

11.1 Installation data

Minimum distance from the lower edge of the hood
body:
to ceramic and cast cooking hobs
to gas hob
to hobs with coal/oil/wood firing
Only connect the appliance to the power
supply once it is properly installed.
11.2 Using the extractor hood as an exhaust air
hood (with air extracted to outdoors)
If the extractor hood has been fitted at the factory
with a carbon filter, this must be removed.
It is only practicable to use this when operating your
hood in circulation mode.
6
GB
try to repair the
65 cm
70 cm
85 cm.