Inhaltsverzeichnis
Werbung
Optional Features Explained
Optionale Einstellungen – Tabelle der Funktionen
THE FOLLOWING SETTINGS ARE OPTIONAL AND IN MOST CASES
FUNKTION
NEED NOT BE ADJUSTED.
Kopplung mit App
Kopplung mit App
Pairing With the App: This function is used to pair the SmartStat to the SmartStat App.
WiFi-Setup
WiFi Set-Up: This function is used to connect the SmartStat with the WiFi network.
Schaltdifferenz
Schaltdifferenz
Switching Differential:
Temperatur bei Abwesenheit
the thermostat. The default is 0.5°C which means that with a set temperature of 20°C, the
Output-Verzögerung
Output-Verzögerung
thermostat will switch the heating on at 19.5°C and off at 20.0°C. With a 1°C differential,
Auf/Ab Temperaturbegrenzung
the heating will switch on at 19.0°C and off at 20.0°C.
Sensorauswahl
Sensorauswahl
Away Temperature: This is the temperature maintained when the thermostat is in Away
Mode. The range is 7 - 17°C. The default is 12°C and is suitable for most applications.
Output Delay: To prevent rapid switching, an output delay can be entered.
Bodentemperaturbegrenzung
This can be set from 00 - 15 minutes. The default is 00 which means there is no delay.
Optimaleinschaltung
Optimaleinschaltung
Temperature Up/Down Limit: This function allows you to limit the use of the up and
Änderungsrate
down temperature arrow keys. This limit is also applicable when the thermostat is locked
Programm-Modus
Programm-Modus
and so allows you to give others limited control over the heating system.
Sensor Selection: On this SmartStat, you can select which sensor should be used. You can
select between air temperature only, floor temperature, or both. When you enable both
Temperaturformat
sensors, the floor sensor is used as a floor limiting sensor and is designed to prevent the
Umgebungslicht-Abdunkelung
Umgebungslicht-Abdunkelung
floor from overheating.
27
EINSTELLEN
Zur Herstellung der Verbindung zum SmartStat App
Zur Herstellung der Verbindung zum SmartStat App
Zum Anschluss an das WiFi-Netzwerk
0,5° - 3,0°C (0,5°C = Standard)
0,5° - 3,0°C (0,5°C = Standard)
This function allows you to increase the switching differential of
7° - 17°C (12°C = Standard)
00 - 15 Minuten (00 = Standard)
00 - 15 Minuten (00 = Standard)
00° - 10°C (00 = Standard)
Integrierter Sensor (Standard)
Integrierter Sensor (Standard)
Luftfernsensor
Luftfernsensor
Nur Bodensensor
Nur Bodensensor
Integrierter & Bodensensor
Integrierter & Bodensensor
Luftfern- & Bodensensor
Luftfern- & Bodensensor
20°C - 45°C (27°C = Standard)
00-05 Stunden (00 = standardmäßig deaktiviert)
00-05 Stunden (00 = standardmäßig deaktiviert)
Minuten zur Erhöhung der Temperatur um 1°C
Werktag/Wochenende (Standard)
Werktag/Wochenende (Standard)
7-Tage-Programmierung
7-Tage-Programmierung
24-Stunden-Modus
24-Stunden-Modus
Nicht programmierbar
Nicht programmierbar
00 = °C, 01 = °F (00 = Standard)
Ein / Aus
Ein / Aus
Werbung
Inhaltsverzeichnis
