Specifications; Additional Safety Rules - Makita 9047 Betriebsanleitung

ENGLISH
1 Wheel guard
2 Screw
3 Notch
4 Side grip
5 Lock nut

SPECIFICATIONS

Model
Depressed center wheel diameter ........................ 180 mm
No load speed (RPM) ........................................... 8,500
Overall length ........................................................ 470 mm
Net weight ............................................................. 4.8 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
For models 9047, 9049, 9057 and 9059, public
low-voltage distribution systems of between
220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.22 (for 9047
and 9049) / 0.24 (for 9057 and 9059) Ohms it can be
presumed that there will be no negative effects.
The mains socket used for this device must be
protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always be sure that the tool is switched off
and unplugged before carrying out any work
on the tool.
2. Keep guards in place.
3. Use only wheels having a maximum operating
speed at least as high as ''No Load RPM''
marked on the tool's nameplate.
When using depressed center wheels, be sure
to use only fiberglass-reinforced wheels.
4. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
5. Use only flanges specified for this tool.
4
Downloaded from www.Manualslib.com
Explanation of general view
6 Depressed center wheel
7 Inner flange
8 Super flange
9 Lock nut wrench
0 Shaft lock
manuals search engine
9047/9047S 9057/9057S
9047F/9047SF 9057F/9057SF 9049F/9049SF 9059F/9059SF
180 mm
8,500
470 mm
5.1 kg
6. Do not damage the spindle, the flange (espe-
cially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
7. Keep hands away from rotating parts.
8. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
9. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced wheel.
10. Use the specified surface of the wheel to
perform the grinding.
11. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other per-
sons or flammable materials.
12. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
13. Always wear safety goggles and ear protec-
tors during operation.
14. Position the tool so that the power cord
always stays behind the tool during operation.
15. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
16. Do not use the tool on any materials contain-
ing asbestos.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing wheel guard (Fig. 1)
When installing a depressed center wheel or an
abrasive cut-off wheel, always use a wheel guard.
Mount the wheel guard with the tab on the wheel
guard band aligned with the notch on the bearing box.
Then rotate the wheel guard 160 degrees counter-
clockwise. Be sure to tighten the screw securely.
q Switch trigger
w Lock lever
e Brush holder cap
r Screwdriver
9049/9049S 9059/9059S
230 mm 230 mm
6,600 6,600
470 mm 470 mm
4.8 kg 5.1 kg