Kinderkraft JULI Bedienungsanleitung Seite 27

IX ASSEMBLING THE CAR SEAT ON THE BUGGY FRAME
The supplied adapters (L) are compatible with the following car seats: Kinderkraft, Maxi Cosi®, Cybex® and are suitable
for models: Kinderkraft MINK, Cybex Aton, Aton 2, Aton Q i Maxi Cosi Mico, Mico AP, Mico NXT, Mico Max 30, Citi, Cabrio,
and CabrioFix.
Place adapters in the openings on both sides of the frame until you hear the lock click (FIG. 31). The adapters should be
tilted slightly toward the parent pushing the buggy.
When installing the car seat on the buggy frame, insert the adapters in the slots on each side of the seat, in accordance
with the seat user manual. Example for KinderKraft MINK is shown in Figure 32. To remove the seat with adapters from
the frame, press the buttons in the adapters on both sides of the buggy (FIG. 33) and pull the seat up.
WARNING! The seat must be always placed on the frame back
to the direction of travel (the child should face the person
pushing the buggy).
X BUGGY DISASSEMBLY
To remove the safety bar push the buttons on its sides and pull it up (FIG. 34).
The hood may be removed quickly by pressing the buttons on the sides of the frame and opening the zip fastener (FIG.
35).
Remove the seat/bassinet from the frame − push the buttons on both sides and pull up (FIG. 36). To fold the frame, press
the lock button located on the handle simultaneously pressing the folding button and push the handle down (FIG. 37).
The frame should be blocked with the side lock (FIG. 38).
WARNING! Do not disassemble the buggy without removing the
bassinet/seat/car seat first.
For cleaning, the bassinet/seat cover can be removed. First, pull the belts out (Section VIII) and remove the hood and the
footmuff. Then open the zip fastener around a portion of the frame (FIG. 39). Release the snap fasteners holding the bar
under the bassinet/seat (FIG. 40). Disconnect the second part of the frame by releasing the snap fasteners on the sides
and pulling the tube out (FIG. 41). Then slide the cover down the tube (FIG. 42). At the end, detach the Velcros on the
underside of the cover and pull the back and seat supports (FIG. 43). The footrest support is made of a material resistant
to moisture.
Installation of the cover takes place in reverse order. During installation of the cover make sure that the groove in the
detachable tube is at the top of the bassinet/seat.
XI CARE AND MAINTENANCE
The buyer is responsible for proper installation of all functional elements as well as for carrying out all required
maintenance and adjustments in order to keep the buggy in good technical condition.
The buggy must be periodically checked for potential problems. Significant measures to be applied to ensure the child's
safety and prevent shortening of the product life have been presented below:
• Check the strength and safety of all rivets and connections.
• Check all wheel locking equipment and tyres. If necessary, replace or repair.
• Check if all safety devices work properly, particularly the main and additional fasteners that should move freely at any
time.
Please, stop using the buggy if there are doubts as to its proper use or a suspicion of any danger.
If the wheels squeak, apply a thin layer of silicone. Do not use oil or grease based products as they attract dirt, which
makes buggy movement difficult.
XII CLEANING
If the elements of the buggy chassis have been exposed to saltwater, rinse with tap water as soon as possible.
Wash at max. 30°C, gentle process.
Do not bleach
Do not dry in a tumble dryer
Do not fold or store the product when it is wet and never store it in wet conditions, as it can lead to mould growth.
XIII Warranty
1. All Kinderkraft products are covered by a 24-month warranty. The warranty period begins on the date of releasing
the product to the Buyer.
Do not wash. Clean the product gently with a
damp cloth and a mild detergent.
Do not iron
Do not dry clean
27