VERTO 50G273 Bedienungsanleitung Seite 11

GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
CORDLESS DRILL
50G273
CAUTION: BEFORE USING THE POWER TOOL READ THIS
MANUAL CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SPECIFIC REGULATIONS REGARDING SAFE USE OF THE
DRILL
• Use ear protectors and safety goggles when operating
the drill. Exposure to noise may cause hearing loss. Metal dust
and other particles floating in the air may cause permanent
eye injury.
• Use additional handles supplied with the tool. Loss of
control may cause operator personal injury.
ADDITIONAL RULES FOR SAFE DRILL OPERATION
• Use only recommended battery and charger.
• Always keep the battery away from sources of fire. Do not
leave the battery for a long time in high temperature (in
direct sunlight, in proximity of heaters and wherever the
temperature exceeds 50°C).
• The battery charging time cannot be longer than 8 hours,
otherwise the battery may be damaged.
• Battery charging process should be supervised by the user.
• Avoid charging the battery in temperature below 0°C.
• Charger supplied with the drill is designed for operation
with this product only. Do not use it for other purposes.
• Do not put any metal objects into the charger.
• Do not change direction of spindle rotation when the tool is
operating. Otherwise the drill may be damaged.
• Use soft, dry cloth to clean the drill. Never use detergents
or alcohol.
• Disconnect the charger from power supply before cleaning.
• If you intend to charge more than one battery successively,
make a 30 minute break between charges.
SPECIAL SAFETY CONDITIONS FOR CHARGER
OPERATION
• Check condition of the charger, cable and plug before each
use. Do not use the charger when it is damaged.
• Keep this manual. It contains important charger use and
safety instructions.
• Before using the charger, read all relevant information
contained within this manual, see markings on the charger
and the product it is designed for.
• To reduce the risk of potential body injury use the charger
for charging Li-Ion batteries only. Other type batteries may
explode and cause personal injury or material damages.
• Do not expose the charger to humidity or water.
• Use of any connecting elements not supplied or not
recommended by the manufacturer of the charger may
cause fire, personal injury or electric shock.
• Make sure the power cord is not located in a pathway, is not
exposed to treading or other danger (e.g. strong tension).
• Do not use extension cord unless absolutely necessary. Use
of improper extension cord may cause fire or electric shock.
When it is necessary to use extension cord, first make sure
that:
– Extension cord socket matches plug prongs of the original
charger power cord.
– The extension cord is in good technical condition.
• Do not use the charger with damaged cord or plug. Damage
should be repaired by a qualified person.
• Do not use the charger after it has been hit, dropped or
otherwise damaged. Entrust the testing and potential repair
to an authorized service workshop.
• Do not try to disassemble the charger. All repairs should be
made at an authorized service workshop. Improper charger
assembly may cause electric shock or fire.
• Disconnect the charger from power supply before starting
any maintenance or cleaning.
• In case of battery damage or improper use it may produce
gas. When it occurs, ventilate room and seek medical
attention in case of medical symptoms.
• Keep the charger clean. Dirt can be the cause of electric
shock.
• Do not use the charger when placed on flammable surface
(e.g. paper, textiles) or in proximity of flammable substance.
Greater charger temperature when charging increases risk
of fire.
When the charger is not in use, it should be disconnected
from mains network.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures
and additional safety systems are used, nevertheless
there is always a small risk of injuries at work.
Li-ion batteries may leak, set on fire or explode when
heated to high temperature or short-circuited. Do not
store the batteries in a car in hot and sunny days. Do
not open the battery. Li-ion batteries contain electronic
protection devices that, if damaged, may cause fire or
explosion of the battery.
CONSTRUCTION AND USE
Drill is a battery powered tool. Drive consists of a commutator
DC motor with planetary gear. The drill is designed for
screwing in and out screws and bolts in wood, metal, plastics
and ceramics, and for drilling holes in such materials. Quick
and tool-free removal of the drill chuck allows to install single-
ended driver bits with different lengths and with hexagonal
shanks, sized 6.35 mm (1/4"), directly on the spindle . An
advantage of the solution is operability in hard to reach areas.
Cordless, battery-powered power tools are especially useful
for works in interior furnishing, adaptation of premises etc.
Use the power tool in accordance with the manufacturer's
instructions only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on
the drawing pages of this manual.
Quick-release chuck
1.
Torque adjustment ring
2.
Gear switch
3.
Direction selector switch
4.
Battery lock button
5.
Battery
6.
Switch
7.
Illumination
8.
11