Introduction; Description; Technical Data - Elettro 205 STANDARD Bedienungsanleitung

ENGLISH
Contents
INTRODUCTION ...................................................................................... 20
DESCRIPTION .......................................................................................... 20
TECHNICAL DATA ................................................................................... 20
TYPES OF MACHINES ............................................................................. 21
INSTALLATION ........................................................................................ 21
EQUIPMENT OF WELDING MACHINES ................................................ 21
CONNECTION TO THE ELECTRICAL POWER SUPPLY ........................... 21
CONTROL APPARATUS ........................................................................... 22
CONNECTION OF THE WELDING TORCH ............................................. 23
CONNECTION OF THE WELDING WIRE AND ADJUSTMENT
OF GAS FLOW ......................................................................................... 23
ADJUSTMENT OF WELDING PARAMETERS .......................................... 24
WELDING WORK CYCLES ....................................................................... 28
RATING PLATE SYMBOLS ....................................................................... 49
RECOMMENDED ADJUSTMENT OF WELDING PARAMETERS ............ 50
ELECTRICAL DIAGRAM .......................................................................... 52
LIST OF SPARE PARTS ............................................................................. 57
TROUBLE SHOOTING LIST ..................................................................... 64
WARRANTY CERTIFICATE ...................................................................... 70
Table 1

Technical data

Mains voltage 50/60 Hz
Welding current range
Output voltage settings
Regulation steps
Duty cycle
Duty cycle 60 %
Duty cycle 100 %
Mains current/input 60 %
Winding
Mains protection-slow, D
Wire feeder
Standardly equiped roll
Wire feed speed
Diameter of wire - Fe
- Al
- Tube wire
Digital voltampermeter
Protection degree
Insulation class
Standards
Dimensions LxWxH
Weight
20 | EN
205
[ V ] 3 x 400
[ A ] 40 - 190
[ V ] 19 - 39
-
[ A ] 190 (15 %)
[ A ] 95
[ A ] 80
[ A/kVA ] 5 / 3.4
- Cu
[ A ]
- 2-roll
- 0.6 - 0.8
[ m/min ]
0.6 - 0.8
[ mm ] 0.8 - 1.0
0.8 - 1.0
- PROCESSOR and SYNERGIC only
- F
-
[ mm ]
[ kg ] 52

Introduction

Thank you for purchasing one for our products.
Before using the equipment you should carefully read
the instructions included in this manual.
It is also necessary to read all the safety regulations in the enclosed docu-
ment „Safety instructions and maintenance".
In order to get the best performance from the system and ensure that its
parts last as long as possible, you must strictly follow the usage instructions
and the maintenance regulations included in this manual. In the interest of
customers, you are recommended to have maintenance and, where nece-
ssary, repairs carried out by the workshops of our service organisation, since
they have suitable equipment and specially trained personnel available. All
our machinery and systems are subject to continual development. We must
therefore reserve the right to modify their construction and properties.

Description

205, 225, 245, 2200, 2400 are professional welding machines designed for
MIG (Metal Inert Gas) and MAG (Metal Active Gas) welding. They are sour-
ces of welding current with flat characteristics. It concerns welding in pro-
tection atmosphere of active and intact gases when added material is in a
form of „infinite" wire supplied into the weld by the wire feeding. These
methods are very productived, especially for the welds of construction steel,
low steel, aluminium and its alloys.
The machines have been designed as movable sets, differing from each
other in their efficiency. The source of welding current, wire supply and feed
are in one compact metal case with two fixed and two turning wheels.
Machines have been designed for welding of thin and medium thickness
materials for wires used from 0.6 to 1.0 mm. Standard equipment of machi-
nes can be found in Chapter „Equipment of machines". Welding machines
confirm to all European Union and The Czech Republic standards and di-
rectives in force.
225 245
3 x 400 3 x 400
30 - 195 30 - 195
19 - 34 19 - 34
10
195 (25 %) 195 (25 %)
150 160
120 140
6.8 / 4.6 6.8 / 4.6
Cu Cu
16
2-roll 2-roll
0.8 - 1.0 0.8 - 1.0
1 - 20
0.8 - 1.0 0.8 - 1.0
0.8 - 1.0 0.8 - 1.0
0.8 - 1.0 0.8 - 1.0
IP 21 S
F F
EN 60974-1, EN 60974-5, EN 60974-10
791 x 488 x 645
62 62
2200 2400
3 x 400 3 x 400
40 - 190 30 - 215
19 - 39 20 - 36,5
190 (30 %) 215 (40 %)
150 190
135 170
7.3 / 4.7 10.5 / 6.7
Cu Cu/Al
4-roll 4-roll
0.6 - 0.8 0.8 - 1.0
0.6 - 0.8 0.8 - 1.0
0.8 - 1.0 0.8 - 1.0
0.8 - 1.0 0.8 - 1.0
PROCESSOR only
F, H F, H
884 x 486 x 655
56 65