Before Starting The Equipment - EINHELL GE-LS 18 Li Originalbetriebsanleitung

The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 61.2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 81.2 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_GE_LS_18_Li_SPK9.indb 18 Anl_GE_LS_18_Li_SPK9.indb 18
≤ 2.5 m/s
2
h
2
- 18 -
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Danger!
The electric power tool generates an electro-
magnetic fi eld during operation. Under certain
circumstances this fi eld may actively or passively
impede medical implants. To reduce the risk of
serious or fatal injuries, we recommend persons
with medical implants to consult their doctor and
the manufacturer of the medical implant prior to
using the equipment.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Removing the blade guard hood (Fig. 2)
Check the fastener on the blade guard hood
when you want to remove the hood. Use a pair of
scissors or side-cutters to remove the cable-tie
from the blade guard hood. Remove the blade
guard hood by unfolding it.
5.2 Fitting the battery (Fig. 3)
Press the pushlock button (A) of the rechargeable
battery and press the rechargeable battery into
the mount provided. Make sure that the pushlock
button latches in place. To remove the rechargea-
ble battery, proceed in reverse order.
5.3 Charging the Li battery pack (Fig. 3-4)
1. Remove the battery pack from the handle,
pressing the pushlock button (A) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate. Insert the po-
wer plug of the charger into the socket outlet.
15.09.2020 09:40:06 15.09.2020 09:40:06