Led Strip Light And Tank Maintenance; Cleaning The Led Strip Light; Saltwater Aquariums; Replacement Parts - Fluval Roma Gebrauchsanleitung

Troubleshooting
If the LED Strip Light does not turn on, please proceed as follows:
PROBLEM
Missing connection of the LED Driver to the power outlet Connect the LED Driver to the power outlet
The lighting is
not working
Missing connection of the lighting unit to the LED Driver
If the problem is not solved after following the above, please contact your Hagen retailer.
AQUARIUM MODEL
LED STRIP LIGHT UNIT
LED STRIP LIGHT MODEL
LUMINAIRE WATTAGE
LUMENS
LUMINAIRE OPERATING VOLTS
LED DRIVER TYPE
LED DRIVER INPUT VOLTS
X = B FOR UK PLUG X = V FOR EU PLUG X = U FOR US PLUG
AQUARIUM MODEL
LED STRIP LIGHT UNIT
LED STRIP LIGHT MODEL
LUMINAIRE WATTAGE
LUMENS
LUMINAIRE OPERATING VOLTS
LED DRIVER TYPE
LED DRIVER INPUT VOLTS
X = B FOR UK PLUG X = V FOR EU PLUG X = U FOR US PLUG

LED STRIP LIGHT AND TANK MAINTENANCE

Cleaning the LED Strip Light

Disconnect the Strip Light from power supply before any maintenance operation.
WARNING: Be sure you unplug the LED driver from the power outlet; just switching off the
lights with the APP is NOT enough because it does not stop the power supply. Never place the
LED Strip Light under water jets or submerge in water.
No special maintenance is required for the Fluval LED Strip Light and Canopy, other than periodic cleaning with a damp
cloth (never use harsh chemical products or detergents). To remove calcareous deposits, it is recommended to use a mild
acid such as lemon juice, followed by a thorough wipe down with a damp cloth to remove any residue.

Saltwater aquariums

It is commonly known that salt water is far more corrosive, conductive (of electricity) and generally degrades both plastic
and metal parts at an accelerated rate versus fresh water. To minimize salt accumulations on the Fluval Canopy and on the
LED Strip Light, it is recommended to take note of the following helpful tips:
1. Make sure filter outputs do not spray above the water surface, position them below the water surface with a slight
downward angle, but still allow for surface movement (contributes to oxygenation).
2. If an air pump must be used, frequent removal of salt deposits will be necessary.
3. Keep the water level as constant as possible (regular top-ups due to evaporation). This is beneficial in providing stable
salinity and will help protect the canopy.
4. It is recommended to regularly clean all LED Strip Light components and the Canopies that come into contact with salt
water at least every 15 days. The cleaning should be carried out with a wet cloth (never use harsh chemical products
or detergents). Simple lemon juice may be used to take away salt accumulation. Afterwards rinse carefully to eliminate
every residue of acid.

REPLACEMENT PARTS

Always use genuine Fluval Spare Parts to guarantee continued performance and safety.
For a full listing of replacement parts please visit www.fluvalaquatics.com.
CAUSE
ROMA LED STRIP LIGHT IDENTIFICATION CODES
ROMA 90
BT Led Unit Roma 90
A13291
12.5W
1000lm
24Vdc
S012BE [X] 2400050
100-240 Vac
VICENZA and VENEZIA LED STRIP LIGHT IDENTIFICATION CODES
VICENZA 180
BT Led Unit Vicenza 90
A13296
26W
2200lm
24Vdc
S024AM[X] 2400100
100-240Vac
Connect the lighting unit to the LED Driver with its con-
nector
ROMA 125
BT Led Unit Roma 125 BT Led Unit Roma 200
A13292
16.5W
1300lm
24Vdc
S018BA[X] 2400063 S024AM[X] 2400100
100-240 Vac
VICENZA 260
BT Led Unit Vicenza 260 BT Led Unit Venezia 190
A13297
48W
4000lm
24Vdc
S050F[X] 2400200 S024AM[X] 2400100
100-240Vac
SOLUTION
ROMA 200 ROMA 240
BT Led Unit Roma 240
A13293 A13294
21W
1600lm 1950lm
24Vdc
S024AM[X] 2400100
100-240 Vac 100-240 Vac
VENEZIA 190 VENEZIA 350
BT Led Unit Venezia 350
A13298 A13299 + A13300
26W 16.5W+37W
2200lm 1300lm + 3100lm
24Vdc
S018BA[X]2400063 (A13299) +
S040Q[X] 2400150 (A13300)
100-240Vac 100-240Vac
24W
24Vdc
24 Vdc
11