Tips For Dispensing Hotter Coffee; Rinsing; Making Several Cups Of Coffee With The Jug Function - Electrolux ECG6600 Gebrauchsanweisung

822_949_354 ECG6600-East_Elux.book Seite 122 Freitag, 1. Februar 2008 11:36 23
g
7.1

Tips for dispensing hotter coffee

• If you want to make enough coffee
for a small cup (less than 60 ml)
immediately after switching on the
coffee machine, use the hot water
from the rinsing procedure to
preheat the cups.
• Set a higher coffee temperature in
the appropriate menu, see „Setting
the coffee temperature" page 127.
• If you have not dispensed any coffee
for a long time with the appliance
switched on, you should first rinse
the system to preheat the brewing
unit. Select the rinsing function
from the appropriate menu (see
„Rinsing" page 122). Let the water
run into the drip tray underneath.
You can also use this water to warm
up the cup that you are using for the
coffee. In this case simply let the hot
water run into the cup (and then
empty it).
• Do not use cups that are too thick,
unless they are preheated, as they
absorb too much heat.
• Use preheated cups by rinsing them
out with warm water or leaving
them at least 20 minutes on the
heated cup tray (H) when the coffee
machine is switched on.
7.2

Rinsing

Rinsing allows the brewing unit and
the coffee dispenser to heat up.
Rinsing only take a few seconds.
0 Press the "MENU" button (Figure 5).
The menu option «CHOOSE LAN-
GUAGE» appears.
0 Press the scrolling buttons "<" or ">"
(Figure 6) until the menu option
«RINSING» appears.
0 Confirm the menu option with the
"OK" button (Figure 6). The display
shows «RINSING» and a progress bar
shown with a percentage
«
After rinsing the appliance automati-
cally returns to coffee mode.
122
8 Making several cups of
coffee with the jug
function
Using this function you can
makeseveral cups of coffee fully
automatically in thestainless steel jug
supplied: Milling, portioning, pressing,
pre-brewing, brewing and disposing
the brewed coffee grounds as
described in the preceeding section.
The appliance is preset to a medium
cup size and normal coffee strength.
You can set your preferred cup size and
coffee strength as „Setting the jug pro-
gramme (Coffee strength and filling
quantity for the jug)" page 127
described underneath.
0 Turn the lid on the stainless steel jug
supplied to the removal position (Fig-
ure 17) and remove the lid. Rinse the
jug and the lid.
0 Put the lid in the pouring position (Fig-
ure 18) on the jug and place this
underneath the coffee dispenser (D).
The coffee dispenser must be pushed
right to the tip so that the jug can be
pushed into position.
The display continusously shows «FILL
BEAN CONT. AND WATER
TANK, EMPTY WASTE CONT.,
PRESS OK», reminding you of the
basic steps necessary to be able to
make a series of coffees in the jug.
0 Make sure that the water tank is full,
that there are enough coffee beans in
the bean container and that the waste
coffee container is empty. Then press
the "OK" button (Figure 6).
The display shows the coffee strength
on the top line, as it is set in the "jug"
menu, e.g. «EXTRA-MILD JUG». The
scrolling buttons "<" or ">" appear on
the bottom line, as does the number of
cups to be made in the jug, e.g.
«<
40%».
3 If you want to change the coffee
strength and the filling quantity for
the jug function, proceed as described
> 4».