Brief Description Of The Press Device - NovoPress ACO102 Betriebsanleitung

7

Brief description of the press device

7.1 Automatic press cycle (Fig. 1))
The device features an automatic press cycle. This ensures that the pressing operation is always
completed. The automatic press cycle is only activated after approx. 1 second. After the automatic
press cycle has been triggered, the green LED (2) goes out and the pressing operation runs
automatically. The pressing operation can then only be stopped by pressing and holding release
button (5). After the pressing operation has been completed, the motor automatically switches off and
the green LED (2) lights up again.
If the start button (1) is released before the automatic press cycle begins, the piston in the press
device moves back to its starting position. The pressing operation will not have been completed. The
pressing operation must be triggered again.
Pos : 36 /RVT/Kurz bes chr eibung/Dr ehbarer Kopf/AC O102, ACO152, AC O202XL @ 0\mod_1382359417950_18.doc x @ 1371 @ 2 @ 1
7.2 Rotatable head
The press tool is equipped with a rotatable crimping head. The head is rotatable by 180°. Within the
range of these 180° the crimping head can be moved into any position. It is only possible to adjust the
crimping head before the pressing operation. The crimping head cannot be rotated while the pressing
operation is being performed.
Pos : 37 /RVT/Kurz bes chr eibung/Entlastungs knopf/AC O102, ACO152, AC O/ECO202, AC O202XL @ 0\mod_1382425726244_18.doc x @ 1401 @ 2 @ 1
7.3 Release button (Fig. 1)
The pressing operation can be stopped at any time by pressing and holding the release button (5).
The piston in the press device then returns to its starting position.
Pos : 38 /RVT/Kurz bes chr eibung/Akku allgemei n/Ü bers chrift/AC O102, ACO152, ACO202XL, AXI/AAP102, @ 0\mod_1382447195475_18.doc x @ 1453 @ 2 @ 1
7.4 Battery
Pos : 39 /RVT/Kurz bes chr eibung/Akku allgemei n/Info: nic ht geladen + T emperatur enACO102, AC O152, ACO/EC O202, ACO202XL, AFP/EF P202, AXI/AAP102 @ 2\mod_1469431352019_18.doc x @ 21590 @ @ 1
Information!
The batteries are not charged at the factory.
Therefore:
–
Information!
Limited temperature range for charging and storing the batteries.
Therefore:
–
Pos : 41 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku abnehmen + aufsetzen/ACO102, ACO152, AC O/ECO202, AC O202XL, AF P/EFP202 @ 0\mod_1382442983216_18.doc x @ 1433 @ @ 1
Removing the battery (Fig. 2)
Push in (1) the two release buttons (A) and then remove the battery (2).
Inserting the battery (Fig. 3)
Slide the battery into the device as illustrated until it clicks into place.
Pos : 42 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku Z ustands anzeig e/AC O102, ACO152, AXI/AAP102 @ 0\mod_1382444821884_18.doc x @ 1440 @ @ 1
Battery charge indicator (Fig. 2)
The 4 green LEDs (4) indicate the charge level of the battery. The number of LEDs lit up denotes the
battery charge. If the LED (2) is flashing, the battery is empty and no further travel is possible.
Pos : 43 /RVT/Kurz bes chr eibung/Ger ät + Akku/AC O102 @ 0\mod_1382524309933_18.doc x @ 1481 @ 2 @ 1
7.5 ACO102 and battery
Information!
The ACO102 press device must only be operated with 12 V lithium-ion rechargeable
batteries. The 12 V battery must only be used in the appropriate press devices.
Feature of the press device after extended periods out of use or when changing the battery:
If the press device is out of use for approx. 30 minutes or the battery is reinserted, it switches off. No
LED is lit up any longer. Press the start button (1) briefly to start the press device.
Charge the batteries before using for the first time.
It is imperative that the operating instructions for the battery charger are complied
with.
15
ACO102
EN