Klick Mini Standard / Klick Carbon Standard Version Operation; User Interface; Turning On And Setting Up The Device; Use - Klaxon KLICK electric-Serie Gebrauchsanleitung

16. KLICK MINI STANDARD / KLICK CARBON STANDARD VERSION OPERATION

16.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and display several
operating parameters (Figure 59).
The number (1) shows the current battery charge level.
The number (2) in the centre of the display shows the speed, in km/h.
The number (3) in the lower part of the display shows the distance travelled, in km.
The number (4) shows the desired maximum speed.
16.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 59).
A. Turning On and Selecting the Speed
Switch on the battery (for more information please refer to the instructions starting from section 18.3).
M
Press and hold the "
+ -
Press the " " e " " buttons to select the desired maximum speed level (shown by the indicator lights in the lower part of the display, number
(4) in the legend); various speed levels can be selected, between 0 (no indicator light on, motor disabled), 1 (minimum speed, 5 km/h), 2
(normal speed, 7.5 km/h), 3 (medium speed, 9 km/h), 4 (high speed, 12 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
After turning on the display, the initial screen shows (in number 3) the partial distance (TRIP) of the device in use.
M
Press the " " button once to enter the second screen. It will show the total distance (ODO).
M
Press again the " " button once to enter the third screen. It will display the maximum speed reached (MAX).
M
Press again the " " button once to enter the fourth screen. It will show the average speed (AVG).
M
Press again the " " button once to enter the fifth screen. It will show the approximate distance that can be covered based on the current
battery level (RANGE); this estimate varies according to the maximum speed level selected.
Press again twice the "
C. Resetting data
Once the display has been turned on, press the "
displayed.
+ -
Use the " " and " " buttons to navigate within the MENU and select DISPLAY SETTING; press the "
Once in the submenu, use the "
+
Press the " " button to move from NO to YES; press the "
+ -
Press the " " and " " buttons together for 5 seconds to exit the MENU and go back to the main screen.
D. Screen Backlighting
+
Hold the " " button for 5 seconds to turn on the screen backlight.
To turn off the backlight, press the "
When the device is turned off, the light is also automatically switched off.
E. Speed Hold Function
-
Press the " " button for 5 seconds to turn on the speed hold function. This function accelerates the device up to a speed of 4.5 km/h and
holds it as long as the button is pressed.
When the button is released, the device instantly stops accelerating.
Every action and/or tampering of the display to change performance and KLICK's security is strictly prohibited. The sole and
DANGER
only actions possible are those specified in paragraph 16.2 of this User's Manual.
NOTE: For further information on the display, see www.klaxon-klick.com or contact an authorised KLAXON dealer.

16.3 USE

Figure 61 shows the Standard handlebar of the Klick device and it identifies the elements that make it up (listed below).
1. Handlebar
2. Acceleration control
3. Display
4. Brake lever
Once the device has been installed, the display has been turned on and a speed has been selected, use the accelerator control to make the device
start to move (Figure 31.1). To stop the device, use the brake lever. The KLICK brake is equipped with an additional safety device which deactivates
the motor when the lever is operated (Figure 31.2).
20
KLAXON Mobility GmbH - ENG
" button for 5 seconds, until the display turns on.
M
" button to display the total time the device has been on (TIME).
+
" and "
+ -
" and " " buttons to select TRIP RESET and press the "M" button to enter.
+
" button for 5 seconds again.
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
-
" buttons together for 5 seconds to enter the MENU. Several options will be
M
" button to confirm the selected option.
M
" button to enter the selected submenu.