Documentation; Installation And Coupling; Installation; Coupling Steps - Klaxon KLICK electric-Serie Gebrauchsanleitung

CAUTION: this accessory is not compatible with any of the "Tetra" version models. For additional information, refer to the material (written, audio/
video) on www.klaxon-klick.com or ask an authorized KLAXON dealer.

9.5 DOCUMENTATION

This USER's MANUAL is provided with the Device in printed format and must be stored with the utmost care. If you lose the above documents,
request a copy of them in writing to KLAXON.

10. INSTALLATION AND COUPLING

10.1 INSTALLATION

KLICK devices are provided by KLAXON (or by an authorised technician) only after having pre-installed the coupling set on the wheelchair.

10.2 COUPLING STEPS

During the entire coupling operation, stop in a flat area, as free as possible from uneven ground and away from hazards which
could cause personal injury.
Insert the CROSSBEAM in one of the two CLAMPING RINGS and secure it by inserting the specific PIN (Figure 18).
Insert the CROSSBEAM also in the second CLAMPING RING and secure it by inserting the specific PIN (Figure 19).
Note: The CROSSBEAM can always remain installed on the wheelchair; if necessary (for loading and unloading from vehicles and closing the
folding wheelchair) it can be removed and placed in a safe place.
Insert the CONNECTOR in the square seat of the CROSSBEAM, pressing the lever located on its bottom. Once inserted, release the lever and
make sure that the CONNECTOR is securely locked (Figure 20).
After having inserted the CONNECTOR, the device will be as shown (Figure 21).
To secure the KLICK device to the connection, move the wheelchair into position as shown (Figures 22 and 23). Make sure the opening of the
coupling is placed over the upper pin (Figure 24).
Holding it in place, brake the wheelchair with its brakes and grip the handlebar; lift KLICK until the upper pin is fully inserted in the opening
of the coupling (Figure 25).
At this point, continue to raise the handlebar by pushing it forward until the lower pin is fully engaged with the connection; at that point the
safety button is triggered (Figure 26).
CAUTION!
Once the device is connected to the wheelchair, it is important to ensure that:
The ground clearance of the front wheels of the wheelchair is 4 cm (with the wheelchair empty - Figure 27).
The kickstand is located above the line of the front wheels and placed below the footboard (Figure 28).
If these requirements are not met, never use the device for any reason and immediately contact an authorised KLAXON
CAUTION
service centre.

10.3 WHEELCHAIR

KLICK devices can be installed only on compatible wheelchairs. KLICK products must be only be installed by authorised KLAXON technicians who may
decide, under their own responsibility, if the specific wheelchair can be properly used with the KLICK device.
11. KLICK ELECTRIC STANDARD VERSION / KLICK POWER STANDARD VERSION OPERATION

11.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and display several
operating parameters (Figure 29).
The icon located top left (1) shows the current battery charge level.
The number (2) in the centre of the display shows the speed, in km/h.
The number (3) in the lower part of the display shows the distance travelled, in km.
The number (4) shows the desired maximum speed.
11.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 29).
A. Turning On and Selecting the Speed
Switch on the battery (for more information please refer to the instructions starting from section 18.3).
M
Press and hold the "
+ -
Press the " " e " " buttons to select the desired maximum speed level (viewable in the left panel of the display, number (5) in the legend);
various speed levels can be selected, between 0 (motor disabled), 1 (minimum speed, 3 km/h), 2 (normal speed, 6 km/h), 3 (medium speed,
10 km/h), 4 (high speed, 13 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
After turning on the display, the initial screen shows (in number 3) the total distance (ODO) the device has been used.
M
Press the " " button once to enter the second screen. It will show the partial distance (TRIP - number 3).
KLAXON Mobility GmbH - ENG
" button for 5 seconds, until the display turns on.
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
11