Turning Off And Releasing From The Wheelchair; Klick Race Standard Version Operation; User Interface; Turning On And Setting Up The Device - Klaxon KLICK electric-Serie Gebrauchsanleitung

Once the device has been installed, the display has been turned on and a speed has been selected, use the handlebar (pulling it towards you) to make
the device start to move (Figure 38). To stop the device, use the brake system by pushing the handlebar as shown (Figure 39).
The device is equipped with reverse. To use reverse, press the green button once, then use the handlebar to start moving the device backward.
To return to the forward operation, release the accelerator and press the green button only once.
The reverse button has only luminous warning systems to show whether it is selected or not.
CAUTION This is shown by the button itself: when the button is fully extended (Figure 32) the reverse gear is OFF (light GREEN off).
When the button is fully pressed (Figure 33) the reverse gear is ON (light GREEN on).
After inserting the battery in its housing and locked by turning the key, remove it and put it in a safe place. It is absolutely
CAUTION
forbidden to use the KLICK device with the key insert in the security block.
The reverse button and the display can be installed either on the left or on the right side of the handlebar according to user's preference.
DANGER For installation and positioning of controls (display, reverse button), contact an authorised KLAXON service centre.
DANGER Before using reverse to move the device, make sure that there are no persons, obstacles, stairs, slopes behind the wheelchair.
At each restart pay maximum attention, before accelerating, to check if forward or reverse operation is currently selected,
DANGER
especially when close to obstacles, drop-offs and any other kind of danger.
If obstacles, drop-offs and dangers are too close to be safe, turn off the KLICK device and manually move the wheelchair to
DANGER
a safe place.

12.4 TURNING OFF AND RELEASING FROM THE WHEELCHAIR

To perform the operation properly, carefully follow the following instructions.
Stop the wheelchair on a flat surface.
Apply the brake on the wheelchair.
Turn off the display by pressing and holding the "
Firmly push the quick release lever of the CONNECTOR TETRA sideways to the right. By doing so, the lower pin is automatically released
and the KLICK disengages from the CONNECTOR, lowering the wheelchair and bringing the front wheels in contact with the ground (Figures
40 and 41).
At this point the upper pin will already be pulled out the front hook of the CONNECTOR; release the wheelchair's brakes and push yourself
back to move away from the KLICK device (which in the meantime will remain upright thanks to its KICKSTAND (Figure 42).
Remove the CONNECTOR, pulling the Velcro grip upward and forward (Figure 43).
When releasing the KLICK from the Connector tetra, the wheelchair may be lowered abruptly until the front wheels touch the
DANGER ground. Pay maximum attention to not endanger the top parts of your body (fingers, hands, arms) as they could be hit by the
handlebar or by other parts of the device.

13. KLICK RACE STANDARD VERSION OPERATION

13.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and display several
operating parameters (Figure 60).
The icon located top left (1) shows the current battery charge level.
The number (2) in the centre of the display shows the speed, in km/h.
The number (3) in the left part of the display shows the desired maximum speed level.
The number (4) shows the distance travelled, in km.
The number (5) shows the time the device has been on, in minutes.
The number (6) shows the data regarding the device's motor (power absorption in watts and internal temperature in °C).
The number (7) shows the external temperature, in °C.
13.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 60).
A. Turning On and Selecting the Speed
Switch on the battery (for more information please refer to the instructions starting from section 18.3).
POWER
Press and hold the "
14
KLAXON Mobility GmbH - ENG
M
" button for 5 seconds.
" button for 5 seconds, until the display turns on.
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020