Turning Off And Releasing From The Wheelchair; Klick Race Tetra Version Operation; User Interface; Turning On And Setting Up The Device - Klaxon KLICK electric-Serie Gebrauchsanleitung

After inserting the battery in its housing and locked by turning the key, remove it and put it in a safe place. It is absolutely
CAUTION
forbidden to use the KLICK device with the key insert in the security block.
The brake lever, the accelerator control, the reverse button, the display and the display controls pushbutton panel can be installed either on the left
or on the right side of the handlebar according to user's preference.
For installation and positioning of controls (display, accelerator control, reverse button, brake lever, display controls
CAUTION
pushbutton panel), contact an authorised KLAXON service centre.
CAUTION Before using reverse to move the device, make sure that there are no persons, obstacles, stairs, slopes behind the wheelchair.
At each restart pay maximum attention, before accelerating, to check if forward or reverse operation is currently selected,
CAUTION
especially when close to obstacles, drop-offs and any other kind of danger.
If obstacles, drop-offs and dangers are too close to be safe, turn off the KLICK device and manually move the wheelchair to
CAUTION
a safe place.

13.4 TURNING OFF AND RELEASING FROM THE WHEELCHAIR

To perform the operation properly, carefully follow the following instructions.
Stop the wheelchair on a flat surface.
Apply the brakes on the wheelchair.
Turn off the display by pressing and holding the "
Push the handlebar forward with one hand grasping it in the middle and simultaneously press the release button on the CONNECTOR with
the other hand. This frees the lower pin of the KLICK coupling (Figure 34).
Reduce forward pressure on the handlebar while holding the release button on the CONNECTOR, thus lowering the wheelchair so that its
front wheels make contact with the pavement (Figure 35).
At this point the upper pin will already be pulled out the front hook of the CONNECTOR; release the wheelchair's brakes and push yourself
back to move away from the KLICK device (which in the meantime will remain upright thanks to its KICKSTAND - Figure 36).
Remove the CONNECTOR, pulling the lever located on its bottom (Figure 20).
During the KLICK release operation, pay attention to not endanger the top parts of your body (fingers, hands, arms) as they
DANGER could be affected by the sudden movement of the handlebar (or other parts of the device) if it is released too quickly. To avoid
this danger, after pressing the release button, gently release the handlebar by lowering the wheelchair gradually.

14. KLICK RACE TETRA VERSION OPERATION

14.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and display several
operating parameters (Figure 60).
The icon located top left (1) shows the current battery charge level.
The number (2) in the centre of the display shows the speed, in km/h.
The number (3) in the left part of the display shows the desired maximum speed level.
The number (4) shows the distance travelled, in km.
The number (5) shows the time the device has been on, in minutes.
The number (6) shows the data regarding the device's motor (power absorption in watts and internal temperature in °C).
The number (7) shows the external temperature, in °C.
14.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 60).
A. Turning On and Selecting the Speed
Switch on the battery (for more information please refer to the instructions starting from section 18.3).
POWER
Press and hold the "
UP ARROW
Press the "
display, number (5) in the legend); various speed levels can be selected, between 0 (motor disabled), 1 (minimum speed, 3 km/h), 2 (normal
speed, 6 km/h), 3 (medium speed, 10 km/h), 4 (high speed, 13 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
After turning on the display, the initial screen shows the partial distance (DST – number 4), the partial time the device has been on (TM –
number 5), the motor's current power absorption (MOTOR W – number 6) and the external temperature (number 7).
POWER
Pressing the "
(ODO – number 4), the total time the device has been on (TTM – number 5) and the motor's internal temperature (MOTOR °C – number 6).
16
KLAXON Mobility GmbH - ENG
POWER
" button for 5 seconds, until the display turns on.
DOWN ARROW
" and " " buttons to select the desired maximum speed level (viewable in the left panel of the
" button once will open the second screen, which shows the average speed (AVS – number 2), the total distance
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
" button for 5 seconds.