Klick Monster Standard Version Operation; User Interface; Turning On And Setting Up The Device - Klaxon KLICK electric-Serie Gebrauchsanleitung

Stop the wheelchair on a flat surface.
Apply the brake on the wheelchair.
Turn off the display by pressing and holding the "
Firmly push the quick release lever of the CONNECTOR TETRA sideways to the right. By doing so, the lower pin is automatically released
and the KLICK disengages from the CONNECTOR, lowering the wheelchair and bringing the front wheels in contact with the ground (Figures
40 and 41).
At this point the upper pin will already be pulled out the front hook of the CONNECTOR; release the wheelchair's brakes and push yourself
back to move away from the KLICK device (which in the meantime will remain upright thanks to its KICKSTAND - Figure 42).
Remove the CONNECTOR, pulling the Velcro grip upward and forward (Figure 43).
During the KLICK release operation with the Connector tetra, the wheelchair may drop suddenly until the front wheels touch
DANGER the pavement. Pay attention to not endanger the top parts of your body (fingers, hands, arms) as they could be affected by
the handlebar or other parts of the device.

15. KLICK MONSTER STANDARD VERSION OPERATION

15.1 USER INTERFACE

The device is equipped with a multifunction LCD display, used to switch the device on and off, select the maximum speed and display several
operating parameters (Figure 60).
The icon located top left (1) shows the current battery charge level.
The number (2) in the centre of the display shows the speed, in km/h.
The number (3) in the left part of the display shows the desired maximum speed level.
The number (4) shows the distance travelled, in km.
The number (5) shows the time the device has been on, in minutes.
The number (6) shows the data regarding the device's motor (power absorption in watts and internal temperature in °C).
The number (7) shows the external temperature, in °C.
15.2 TURNING ON AND SETTING UP THE DEVICE (FIGURE 60).
A. Turning On and Selecting the Speed
Switch on the battery (for more information please refer to the instructions starting from section 18.3).
POWER
Press and hold the "
UP ARROW
Press the "
display, number (5) in the legend); various speed levels can be selected, between 0 (motor disabled), 1 (minimum speed, 3 km/h), 2 (normal
speed, 6 km/h), 3 (medium speed, 10 km/h), 4 (high speed, 13 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
After turning on the display, the initial screen shows the partial distance (DST – number 4), the partial time the device has been on (TM –
number 5), the current motor's power absorption (MOTOR W – number 6) and the external temperature (number 7).
POWER
Pressing the "
(ODO – number 4), the total time the device has been on (TTM – number 5) and the motor's internal temperature (MOTOR °C – number 6).
POWER
Pressing the "
electrical tension in volts (VOL. – number 4).
To reset trip data, hold down the "
POWER
the " " button to reset them.
C. Screen Backlighting
UP ARROW
Hold the "
To turn off the backlight, press the "
When the device is turned off, the light is also automatically switched off.
CAUTION: this procedure must also be used to turn on and off the front LED light connected to the RACE battery, if the device is equipped with it
(listed under accessories in the order form).
D. Speed Hold Function
DOWN ARROW
Press the "
4.5 km/h and holds it as long as the button is pressed.
When the button is released, the device instantly stops accelerating.
E. Cruise Control function
To activate this function the speed has to be higher than 8 km/h.
Keep a constant speed for at least 10 seconds and press the "
function, which will run the KLICK at the actual speed; the display at number (3) will show the letter "C" as long as the function is activated.
The Cruise Control function must be activated by one of the following modes: operating on the Brake lever (left or right), operating on the
Accelerator control, pressing one of the buttons on the Display.
ATTENTION: By pressing the Reverse button the Cruise Control function will be NOT switched off.
18
KLAXON Mobility GmbH - ENG
POWER
" button for 5 seconds, until the display turns on.
DOWN ARROW
" and " " buttons to select the desired maximum speed level (viewable in the left panel of the
" button once will open the second screen, which shows the average speed (AVS – number 2), the total distance
" button again will open the third screen, which shows the maximum speed (MXS – number 2) and the motor's
UP ARROW DOWN ARROW
" and "
" button for 5 seconds to turn on the screen backlight.
UP ARROW
" button for 5 seconds again.
" button for 5 seconds to turn on the speed hold function. This function accelerates the device up to a speed of
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
" button for 5 seconds.
" buttons together for 5 seconds; when the data start flashing, press
DOWN ARROW
" key for 5 seconds to automatically insert the Cruise Control