Use; Turning Off And Releasing From The Wheelchair - Klaxon KLICK electric-Serie Gebrauchsanleitung

POWER
Pressing the "
electrical tension in volts (VOL. – number 4).
To reset trip data, hold down the "
POWER
the " " button to reset them.
C. Screen Backlighting
UP ARROW
Hold the "
To turn off the backlight, press again the "
When the device is turned off, the light is also automatically switched off.
CAUTION: this procedure must also be used to turn on and off the front LED light connected to the RACE battery, if the device is equipped with it
(listed under accessories in the order form).
D. Speed Hold Function
DOWN ARROW
Press the "
holds this speed as long as the button is pressed.
When the button is released, the device instantly stops accelerating.
In the Klick Race Tetra version the Cruise Control function, although present, CAN NOT BE USED under any circumstances
DANGER and for any reason; this function is strictly prohibited for safety reasons, safety of the user, persons and / or things that can
be nearby.
Every action and/or tampering of the display to change performance and KLICK's security is strictly prohibited. The sole and
DANGER
only actions possible are those specified in paragraph 14.2 of this User's Manual.
NOTE: For further information on the display, see www.klaxon-klick.com or contact an authorised KLAXON dealer.

14.3 USE

Figure 63 shows the Tetra handlebar of the Klick device and it identifies the elements that make it up (listed below).
1. Tetra handlebar with PUSH AND PULL acceleration/brake system
2. Display
3. Reverse button
4. Display controls pushbutton panel
Once the device has been installed, the display has been turned on and a speed has been selected, use the handlebar (pulling it toward you) to make
the device start to move (Figure 38). To stop the device, activate the brake system pushing it forward (Figure 39).
The device is equipped with reverse. To use reverse, press the red button once; at this point, use the handlebar to make the device start to move
backward.
To return to forward operation, release the accelerator and press again the red button once.
The reverse button has only luminous warning systems to show whether it is selected or not.
This can occur in two ways:
VISUAL-> when button is lifted to the maximum then the reverse gear is DISENGAGED; when the button is turned to
CAUTION
maximum then the reverse gear is ENGAGED.
LUMINOUS > when the reverse gear is ENGAGED, the display flashes off and on repeatedly the backlight. When the reverse
gear is DISENGAGED this function stops responding.
After inserting the battery in its housing and locked by turning the key, remove it and put it in a safe place. It is absolutely
CAUTION
forbidden to use the KLICK device with the key insert in the security block.
The reverse button, the display controls pushbutton panel and the display can be installed either on the left or on the right side of the handlebar
according to user's preference.
For installation and positioning of controls (display, reverse button, display controls pushbutton panel), contact an authorised
DANGER
KLAXON service centre.
DANGER Before using reverse to move the device, make sure that there are no persons, obstacles, stairs, slopes behind the wheelchair.
At each restart pay maximum attention, before accelerating, to check if forward or reverse operation is currently selected,
DANGER
especially when close to obstacles, drop-offs and any other kind of danger.
If obstacles, drop-offs and dangers are too close to be safe, turn off the KLICK device and manually move the wheelchair to
DANGER
a safe place.

14.4 TURNING OFF AND RELEASING FROM THE WHEELCHAIR

To perform the operation properly, carefully follow the following instructions.
KLAXON Mobility GmbH - ENG
" button again will open the third screen, which shows the maximum speed (MXS – number 2) and the motor's
UP ARROW DOWN ARROW
" and "
" button for 5 seconds to turn on the screen backlight.
UP ARROW
" button for 5 seconds to turn on the speed hold function. This function accelerates the device up 4.5 km/h and
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
" buttons together for 5 seconds; when the data start flashing, press
" button for 5 seconds.
17