Use - Klaxon KLICK electric-Serie Gebrauchsanleitung

UP ARROW
Press the "
display, number (5) in the legend); various speed levels can be selected, between 0 (motor disabled), 1 (minimum speed, 3 km/h), 2 (normal
speed, 6 km/h), 3 (medium speed, 10 km/h), 4 (high speed, 13 km/h) and 5 (maximum speed, 15 km/h).
B. Navigating the data
After turning on the display, the initial screen shows the partial distance (DST – number 4), the partial time the device has been on (TM –
number 5), the motor's current power absorption (MOTOR W – number 6) and the external temperature (number 7).
POWER
Pressing the "
(ODO – number 4), the total time the device has been on (TTM – number 5) and the motor's internal temperature (MOTOR °C – number 6).
POWER
Pressing the "
electrical tension in volts (VOL. – number 4).
To reset trip data, hold down the "
POWER
the " " button to reset them.
C. Screen Backlighting
UP ARROW
Hold the "
To turn off the backlight, press the "
When the device is turned off, the light is also automatically switched off.
CAUTION: this procedure must also be used to turn on and off the front LED light connected to the RACE battery, if the device is equipped with it
(listed under accessories in the order form).
D. Speed Hold Function
DOWN ARROW
Press the "
4.5 km/h and holds it as long as the button is pressed.
When the button is released, the device instantly stops accelerating.
E. Cruise Control function
To activate this function the speed has to be higher than 8 km/h.
Keep a constant speed for at least 10 seconds and press the "
function, which will run the KLICK at the actual speed; the display at number (3) will show the letter "C" as long as the function is activated.
The Cruise Control function must be activated by one of the following modes: operating on the Brake lever (left or right), operating on the
Accelerator control, pressing one of the buttons on the Display.
ATTENTION: By pressing the Reverse button the Cruise Control function will be NOT switched off.
During the use of the Cruise Control function it is compulsory to pay the utmost attention to road hazards in order to be able
DANGER
to intervene on the commands promptly avoiding any kind of collision that could cause damage to people and / or things.
Every action and/or tampering of the display to change performance and KLICK's security is strictly prohibited. The sole and
DANGER
only actions possible are those specified in paragraph 13.2 of this User's Manual.
NOTE: For further information on the display, see www.klaxon-klick.com or contact an authorised KLAXON dealer.

13.3 USE

Figure 62 shows the Standard handlebar of the Klick device and it identifies the elements that make it up (listed below).
1. Handlebar
2. Accelerator control
3. Reverse button
4. Display
5. Brake lever
6. Display controls pushbutton panel
Once the device has been installed, the display has been turned on and a speed has been selected, use the accelerator control to make the device
start to move (Figure 31.1). To stop the device, use the brake lever. The KLICK brake is equipped with an additional safety device which deactivates
the motor when the lever is operated (Figure 31.2).
The device is equipped with reverse as standard equipment. To use reverse, press the red button once, then press the accelerator to start moving
the device backward.
To return to the forward operation, release the accelerator and push again the red button once.
The reverse button has only luminous warning systems to show whether it is selected or not.
This can occur in two ways:
VISUAL-> when button is lifted to the maximum then the reverse gear is DISENGAGED; when the button is turned to
CAUTION
maximum then the reverse gear is ENGAGED.
LUMINOUS > when the reverse gear is ENGAGED, the display flashes off and on repeatedly the backlight. When the reverse
gear is DISENGAGED this function stops responding.
KLAXON Mobility GmbH - ENG
DOWN ARROW
" and " " buttons to select the desired maximum speed level (viewable in the left panel of the
" button once will open the second screen, which shows the average speed (AVS – number 2), the total distance
" button again will open the third screen, which shows the maximum speed (MXS – number 2) and the motor's
UP ARROW DOWN ARROW
" and "
" button for 5 seconds to turn on the screen backlight.
UP ARROW
" button for 5 seconds again.
" button for 5 seconds to turn on the speed hold function. This function accelerates the device up to a speed of
KLICK electric series Manual (ENG) - rev.6.3 of 25.05.2020
" buttons together for 5 seconds; when the data start flashing, press
DOWN ARROW
" key for 5 seconds to automatically insert the Cruise Control
15