10
Table of contents
1. Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2. PCB design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Structure of device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 Tear-off contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3 Pull relief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Detector group inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.1 BUS-2 address setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. Installation guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10. Final assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
11. Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Security notes
Read the instructions carefully and thoroughly before installing the device and putting it into
operation. They contain important information on installation, programming and operation.
The device is a state-of-the-art product. Only use the device:
-
in accordance with regulations,
-
iwhen it is has been installed and is functioning correctly,
-
in accordance with technical data
The manufacturer is not responsible for damage that is caused by use not in accordance with regulations.
Installation and programming as well as maintenance and repair work may only be carried out by
skilled, authorized personnel.
De-energize the entire system before soldering and connecting.
Carry out soldering work with a temperature-controlled electrically isolated soldering iron.
Do not use the device in a potentially explosive environment or in rooms where metal
or plastic decomposing vapours are emitted.
Observe the VDE safety regulations and provisions of the local electricity supplier.
Caution
Do not look directly into the light beam of the flashing LEDs - danger to eyes. Do not use tightly
converging instruments (lenses) for observing the light beam. Only use the alarm signalling
device together with the housing cover (glare and diffusor protection).
Mounting and Connection Instructions Sounder/Flasher with 2 Inputs BUS-2
RISK OF GLARE
due to strong light!
AVOID INJURY TO EYES!
The device is equipped with LEDs Class 1M (EN 60825-1).
Page