Before Starting The Equipment - EINHELL TC-TS 210 Originalbetriebsanleitung

and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
Anl_TC_TS_210_SPK9.indb 24 Anl_TC_TS_210_SPK9.indb 24
GB
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the circular saw!
6.1 Fitting/removing the saw blade guard
(Fig. 3)
•
Using the hand wheel (8), set the saw blade
(4) to the maximum cutting depth.
•
Unscrew the rotary knob (35) as far as possi-
ble until the rotary knob (35) touches the self-
locking nut (36).
•
Caution! Do not move the self-locking nut
(36).
•
Push the lock bolt (37) as far as possible
through the saw blade guard (2), so that the
square profile of the lock bolt (37) projects out
of the saw blade guard (2).
•
Holding the lock bolt (37) pressed, guide the
saw blade guard (2) into the L-shaped recess
(18) in the splitter by the lock bolt (37), gui-
ding it forward at first and then downwards.
•
Then push the lock bolt (37) with the square
profile back into the recess in the saw blade
guard (2) with a tight fit.
•
Screw the rotary knob (35) back tightly as far
as it will go. Important! The screw connection
between the lock bolt (37) and the rotary
knob (35) is designed to allow the saw bla-
de guard (2) to be able to move freely at all
times.
•
Warning! The saw blade guard (2) must al-
ways lower to the workpiece automatically
under its own weight.
•
To dismantle, proceed in reverse order.
- 24 -
07.11.2019 08:49:31 07.11.2019 08:49:31