EINHELL TC-TS 210 Originalbetriebsanleitung Seite 27

far toward the blade. The distance between
the stop rail (23) and the blade (4) should be
approx. 2 cm.
•
If necessary, slacken the two knurled screws
(41) and adjust the stop rail (23).
•
Retighten the knurled screws (41).
7.5 Setting the angle (Fig. 15)
•
Undo the locking grip (9).
•
To adjust the angle of the saw blade, push
the hand wheel (8) until the pointer is aligned
with the desired angular setting on the angle
scale.
•
Lock the locking grip (9).
•
If needed, the end stop for adjusting the ang-
le of the saw blade can be readjusted for 0°
and 45°. To do this, adjust the two adjustment
screws (38) and (39).
8. Operation
Warning!
•
After every new adjustment we recommend
you to make a trial cut in order to check the
new settings.
•
After switching on the saw, wait for the blade
to reach its maximum speed of rotation before
commencing with the cut.
•
Take extra care when starting the cut!
•
Never use the equipment without the suction
function.
•
Regularly check and clean the suction chan-
nels.
8.1 Making longitudinal cuts (Fig. 16)
Longitudinal cutting (also known as slitting) is
when you use the saw to cut along the grain of
the wood.
Press one edge of the workpiece against the
parallel stop (7) while the fl at side lies on the saw
table (1).
The blade guard (2) must always be lowered over
the workpiece.
When you make a longitudinal cut, never adopt
a working position that is in line with the cutting
direction.
•
Set the parallel stop (7) in accordance with
the workpiece height and the desired width.
(See 7.3.)
•
Switch on the saw.
•
Place your hands (with fingers closed) flat on
the workpiece and push the workpiece along
the parallel stop (7) and into the blade (4).
Anl_TC_TS_210_SPK9.indb 27 Anl_TC_TS_210_SPK9.indb 27
GB
•
Guide at the side with your left or right hand
(depending on the position of the parallel
stop) only as far as the front edge of the gu-
ard hood.
•
Always push the workpiece through to the
end of the splitter (5).
•
The offcut piece remains on the saw table
(1) until the blade (4) is back in its position of
rest.
•
Secure long workpieces against falling off at
the end of the cut (e.g. with a roller stand etc.)
(e.g. roller table, etc.)
8.1.1 Cutting narrow workpieces (Fig. 17)
Be sure to use a push stick (3) when making lon-
gitudinal cuts in workpieces smaller than 150 mm
in width. A push stick is supplied with the saw!
Replace a worn or damaged push stick immedi-
ately.
8.1.2 Cutting very narrow workpieces (Fig.
18)
•
Be sure to use a push block when making
longitudinal cuts in very narrow workpieces
with a width of 50 mm and less.
•
The low guide face of the parallel stop is best
used in this case.
•
There is no push block supplied with the saw!
(Available from your specialist dealer) Repla-
ce the push block without delay when it beco-
mes worn.
8.2 Making angular cuts (Fig. 15/19)
Angular cuts must always be made using the par-
allel stop (7). If you tilt the saw blade (4) to the left
when making angular cuts, position the parallel
stop (7) on the right-hand side of the saw blade
(4). Guide the workpiece between the saw blade
(4) and the parallel stop (7).
•
Set the blade (4) to the desired angle. (See
7.5.)
•
Set the parallel stop (7) in accordance with
the workpiece width and height (see 7.3)
•
Carry out the cut in accordance with the work-
piece width (see 8.1.1 and 8.1.2).
8.3 Making cross cuts (Fig. 20)
•
Slide the cross stop (14) into the slot (21) in
the saw bench and adjust to the required ang-
le. (See 7.4.)
•
Press the workpiece firmly against the cross
stop (14).
•
Switch on the saw.
•
Push the cross stop (14) and the workpiece
toward the blade in order to make the cut.
- 27 -
07.11.2019 08:49:31 07.11.2019 08:49:31