Intended Use - Makita DFT024F Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening torque
No load speed (RPM)
Dimensions (L x W x H)
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DFT024F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFT025F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFT060F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
Hard joint
Soft joint
with BL1815N battery
with BL1860B battery
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
DFT024F
0.5 - 2 N•m
0.5 - 2 N•m
-1
260 - 1,600 min
161 mm x 75 mm x 242 mm
161 mm x 75 mm x 258 mm
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-2:
Model DFT024F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DFT025F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model DFT060F
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
4 ENGLISH
DFT025F DFT060F
1.5 - 6.5 N•m
1.5 - 6.5 N•m
-1
100 - 1,300 min
D.C. 18 V
1.2 - 1.5 kg
DC18SH
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2
2
) : 2.5 m/s or less
h
2