Intended Use - Makita DFL083F Betriebsanleitung

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Fastening torque
Square drive
*1
No load speed
Rated voltage
Overall length
(Depending on the battery)
Net weight
Applicable USB cable
• Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
*1
• No load speed is adjustable with exclusive application.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.

Intended use

The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DFL083F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFL125F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFL204F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
Model DFL302F
Sound pressure level (L
Uncertainty (K) : 3dB(A)
Model DFL403F
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Hard joint
Soft joint
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
) : 70 dB(A) or less
pA
DFL083F DFL125F
2 - 8 N•m 5 - 12 N•m
2 - 8 N•m 5 - 12 N•m
150 - 700 100 - 700
-1 -1
min min
464 - 481 mm
1.7 - 2.1 kg
BL1415N / BL1415NA / BL1430B / BL1440 / BL1460A / BL1460B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
4 ENGLISH
DFL204F DFL302F
8 - 20 N•m 16 - 30 N•m 25 - 40 N•m
8 - 20 N•m 16 - 30 N•m 25 - 40 N•m
9.5 mm
100 - 440 70 - 230
-1 -1
min min
D.C. 14.4 V
503 - 520 mm
2.0 - 2.3 kg
661432-2
DC18SH
DFL403F
50 - 220
-1
min