Operation; Maintenance; Disposal And Recycling - Scheppach HCE1601 Original Bedienungsanleitung

10. Operation

The equipment consists of an assembly with a pump,
which is encased in a shock absorbing housing. The
equipment comes with a lance and a non-slip gun (for
an optimal working position), whose shape and con-
figuration comply with the applicable regulations.
Commissioning:
Once you have completely assembled the high-pres-
sure cleaner and all connections have been made,
proceed as follows:
Turn on the water supply. Unlock the pistol (10) via
the locking switch (C). Pull back the trigger lever (D)
so that the air in the device can discharge. (fig. 6)
Switch on the device by setting the on/off switch (4)
to "ON". Next, press the trigger lever (D). (fig. 1/6)
To switch off, release the trigger lever (D), and the
device switches to stand-by. The high-pressure
cleaner starts again when you press the trigger le-
ver (D). (fig. 6)
To switch off the high-pressure cleaner completely,
set the on/off switch (4) to "OFF". (fig. 1)
Using the attachments (Fig. 1)
Cleaner container (5): Fill the cleaner container with
the corresponding cleaner. The cleaner is dosed au-
tomatically in low-pressure operation. The flow quan-
tity may be adjusted by turning the nozzle.
Nozzle (7): For tough cleaning work.

11. Maintenance

m Warning! Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
General maintenance measures
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
down with compressed air at low pressure.
• We recommend that you clean the equipment im-
mediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Long periods of nonuse (electric pump)
If the machine is going to be stored for longer peri-
ods of time (i.e. over 3 months) in a room where frost
could develop, it is recommended that the machine
be filled with an antifreeze solution (similar to the
antifreeze solutions used for vehicles).
When the device is not used for an extended period
of time, lime deposits begin to form in the electric
pump, which in turn can lead to starting difficulties.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: hose, lance, Nozzles and attachments,
seals
* Not necessarily included in the scope of delivery!
Cleaning the nozzle (Fig. 1)
Use the supplied nozzle cleaning needle (12) to clean
clogged nozzles.

12. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Never place
defective equipment in your household refuse. The
equipment should be taken to a suitable collection
center for proper disposal. If you do not know the
whereabouts of such a collection point, you should
ask in your local council offices.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not
be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU)
pertaining to waste electrical and electronic
equipment (WEEE). This product must be disposed of
at a designated collection point. This can occur, for
example, by handing it in at an authorised collecting
point for the recycling of waste electrical and electron-
ic equipment. Improper handling of waste equipment
may have negative consequences for the environment
and human health due to potentially hazardous sub-
stances that are often contained in electrical and elec-
tronic equipment. By properly disposing of this prod-
uct, you are also contributing to the effective use of
natural resources. You can obtain information on col-
lection points for waste equipment from your municipal
administration, public waste disposal authority, an au-
thorised body for the disposal of waste electrical and
electronic equipment or your waste disposal company.