Philips HR 1386 Gebrauchsanweisung Seite 5

• Bar blender. Use the bar blender accessory
e.g. for chopping or blending uncooked or
cooked vegetables (dry or with water) or fruit,
and for making soup, purée, mayonnaise,
milkshake, sauces, diet and baby or infant food.
Select speed I first to prevent splashing. Where
possible switch over to speed II.
During use, move the blades unit through the
ingredients. (Do not lift it too high, to prevent
spattering!)
Please note: this appliance is not suitable for
kneading (yeast) dough, shortbread dough and
minced meat. For such heavy applications we
advise you to use a Philips food processor.
Cleaning
- Operate the beaters or blades in soapy water
for a short time.
- Switch off and remove the mains plug from the
wall socket.
- Disassemble the beater or bar blender
attachments from the motor unit.
- Beaters: Depress the ejector knob to release
the beaters (fig. 8).
You may clean the beaters in hot soapy water.
They may also be cleaned in a dishwasher.
- Beaters coupler: Clean with a damp cloth only.
- Bar blender attachment: Do not fully immerse
the attachment. The end with the blades may
be cleaned with hot soapy water using a
washing-up brush.
You can wipe the bar clean with a damp cloth.
- Motor unit: Clean with a damp cloth only.
Wall mounting
You can hang the appliance on the wall, using the
wallrack. Select an appropriate spot, preferably
close to a wall socket.
Keep sufficient free space (min. 25 cm or 10"
above the wallrack and about 20 cm or 8" below
it). You can use the wallrack as a template to
mark the spots for drilling holes. The distance
between the hole markings should be 100 mm
(centre to centre) (fig. 9).
For mounting onto a brick or stone wall, plaster or
tiles: drill two 5 mm (0.2") holes using a masonry
drill and insert the provided plugs.
Let the screw heads protrude 5 mm (fig. 10) and
slide the wallrack into position (fig. 11).
Downloaded from www.Manualslib.com manuals search engine
For U.K. only:
This appliance is supplied with a non-rewirable
13 Amp. plug. The plug must never be used
without the fuse cover being in place.
If a replacement fuse cover is required, it must be
of the same type or colour as the coloured insert
around the fuse cover.
Replacement fuse covers are available from
Electrical Retailers or direct from Philips, tel.
0181 689 2166, extension 8014.
Replacement 3 Amp. fuses must be BSI or ASTA
BS 1362 approved.
Important safety information
If the non-rewirable plug is not suitable for the
socket outlets in your home, it can be removed
and replaced by a plug of the correct type.
The non-rewirable plug must be cut from the
mains cord, the fuse removed, and the plug safely
discarded to prevent further use.
The removed plug can be hazardous if inserted
into a live mains socket.
Wiring Instructions U.K.
"IMPORTANT"
The wires in the mains lead are coloured in
accordance with the following code:
Blue - neutral
Brown - live
As the colours of the wires in the mains lead
of this appliance may not correspond with the
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured Blue must be
connected to the terminal which is marked
with the letter "N" or coloured Black.
The wire which is coloured Brown must be
connected to the terminal which is marked
with the letter "L" or coloured Red.
DO NOT CONNECT either of these wires to
the earth terminal in the plug which is marked
with the letter "E" or by the earth symbol E or
coloured GREEN, or GREEN AND YELLOW.
Note: If the terminals of the plug are
unmarked or if you are in any doubt
consult a qualified electrician.
5