SSS Siedle TCIP 603-03 Produktinformation Seite 10

4 In order to link the TCIP 603-... to
an Ethernet network, connect the
RJ-45 network cable and connect it
on the other side to the network.
5 The simplest connection between
TCIP 603-... and the configuration
and operating PC is using a cross-
over cable).
6 Integration of the TCIP 603-...
in an existing network. This is only
possible if the configuration and
operating PC are located in the same
subnet and use the same address
area, e.g. 192.168.0.xxx
Terminal assignment
E1, E1 Entrance 1
E2, E2 Entrance 2
E3, E3 Entrance 3
E4, E4 Entrance 4
E5, E5 Entrance 5
W0, W1, W2 Output 1
W3, W4, W5 Output 2
W6, W7, W8 Output 3
W9, W10, W11 Output 4
+M, -M Supply voltage
20–30 V DC
Da, Da Vario bus
Wiegand 1 Wiegand card
reader 1
Wiegand 2 Wiegand card
reader 2
LAN 10/100 Network
LED operating displays
• Power
Indicates whether mains power is
available
• Status
Indicates that the TCIP 602-... is
operational
• Error
Indication of error status
• Wiegand 1
Sabotage display for reader 1
• Wiegand 2
Sabotage display for reader 2
• LAN
Network status display
10
• E1–E5
Display input 1 – input 5
• A1–A4
Display output 1 – output 4
Installation
7 Install the TCIP 603-... in accord-
ance with the wiring diagram. If
several input modules are connected
to the TCIP 603--..., the address
(Addr. 1–8) number must be set at
the input modules.
8 Installation of the TCIP 603-...
with the extension FSM 740-... and
SCE 640-...
The TCIP 603-... is connected to a
TCP/IP network via a CAT5 cable at
the LAN socket. In its as-delivered
status, the TCIP 603-... has the IP
address 192.168.0.1 (subnet mask
255.255.255.0). The controller
is configured via a web browser,
meaning that no special software
needs to be installed. Configuration
is possible via any PC connected to
the network PC.
Dialling the TCIP 603-...
• Establish the connection via the
network to the TCIP 603-...
• Start the Internet Explorer or com­
patible browser
• Enter http://192.168.0.1 in the
address line
• The configuration registration
window appears in the browser
• Enter the user name Service and
password Siedle, (case sensitive),
then click the Log in button
Commissioning
The input mask divides into 4 areas:
• Hardware/system
• Configuration
• Reports
• Tools
Hardware/system
• Inputs
Configuration of potential inputs
E1–E5 of the TCIP 603-... e.g. for
call buttons or door sensor.
• Outputs
Configuration of potential-free out­
puts A1–A4
• Readers
Search for all modules for access
control connected to the Vario bus.
Once the modules have been read
in, every module can be assigned an
unambiguous name.
• Network
Change of the fixed IP address,
subnet mask and standard gateway.
It is possible to modify the configu­
ration timeout.
• System time/time change
Setting the date and time
Configuration
• Doors
In this menu, the individual doors
are generated.
• Time profiles
Generation of time profiles
• Public holidays/Vacation
Input of public holidays or days on
which the access control system only
admits certain groups of users.
• Access groups
Up to 40 access groups can be
generated. e.g. IT access group or
cleaning personnel.
• Users
Input of individual users with names
for unambiguous identification. One
user can be assigned to several dif­
ferent access groups.
Reports
• Event log
Display of the last used inputs and
outputs with indication of the user
name and relevant door. Historic
entries can be found using a filter.
• Presence list
Display of currently present persons
who have passed by a connected
module of the access control system.
This function is only possible if
output readers are configured at the
TCIP 603-...