Screen Menu - Sony SDM-P246W Handbuch

x Resetting the adjustment data to the
defaults 0
You can reset the adjustments to the default settings.
1 Press the MENU button.
The main menu appears on the screen.
2 Press the m/M buttons to select
ADJUST) and press the OK button.
The PICTURE ADJUST menu appears on the screen.
3 Press the m/M buttons to select 0 (MODE RESET)
and press the OK button.
The MODE RESET menu appears on the screen.
4 Press the m/M buttons to select the desired mode
and press the OK button.
• OK: To reset all of the adjustment data in the
PICTURE ADJUST menu to the default settings.
• CANCEL:To cancel resetting and return to the PICTURE
ADJUST menu.

SCREEN menu

You can adjust the following items using the SCREEN menu.
• ZOOM
• AUTO ADJUST
• PHASE
• PITCH
• H CENTER
• V CENTER
• RESOLUTION
Note
When receiving digital RGB signals from the DVI-D input connector
for INPUT1/INPUT2, adjustment is unnecessary.
x ZOOM
The monitor is set to display the picture on the screen in full,
irrespective of the picture's mode or resolution in the default
setting (FULL).
You can also view the picture in its actual aspect ratio or
resolution.
Settings in the ZOOM menu can be made for the current input.
You can also adjust settings for other inputs.
Z OOM
F U L L
N O R M A L
R E A L
1 9 2 0
1 Press the MENU button.
The main menu appears on the screen.
2 Press the m/M buttons to select
press the OK button.
The SCREEN menu appears on the screen.
(PICTURE
S C R E E N
Z OOM
A U T O A D J U S T
P H A S E
P T CH I
H C E N T E R
1 9 2 0 x 1 2 0 0 / 6 0 H z
E X I T
x 1 2 0 0 / 6 0 H z
E X I T
(SCREEN) and
3 Press the m/M buttons to select ZOOM and press the
OK button.
The ZOOM menu appears on the screen.
4 Press the m/M buttons to select the desired mode
and press the OK button.
• FULL: The input signal is displayed on the screen in full,
irrespective of the picture's mode or resolution.
• NORMAL: The input signal is displayed on the screen at
its actual aspect ratio. Therefore, black bands
may appear at the right and left of the picture,
depending on the signal.
• REAL: The input signal is displayed on the screen at its
actual resolution. Sub-1920 × 1200 signals are
displayed at the center of the screen surrounded
by a black frame.
Note
When you use 1,920 × 1,200 resolution signals, the above mentioned
settings are not available. The picture is displayed on the screen in full.
x Automatic picture quality adjustment
function (for INPUT3 only)
When the monitor receives an input signal, it automatically
adjusts the picture's position and sharpness (phase/pitch), and
ensures that a clear picture appears on the screen (page 21).
Note
While the automatic picture quality adjustment function is activated, only
1 (power) switch will operate.
If the automatic picture quality adjustment function of this
monitor seems not to completely adjust the picture
You can make further automatic adjustment of the picture quality for the
current input signal. Adjust by pressing the OK button (One touch Auto
adjust), or following the steps in "AUTO ADJUST" below.
If you still need to make further adjustments to the picture
quality
You can manually adjust the picture's sharpness (phase/pitch) and
position (horizontal/vertical position).
These adjustments are stored in memory and automatically
recalled when the monitor receives a previously input and
registered input signal.
x Make further automatic adjustments to the
picture quality for the current input signal
(AUTO ADJUST) (for INPUT3 only)
1 Press the MENU button.
The main menu appears on the screen.
2 Press the m/M buttons to select
press the OK button.
The SCREEN menu appears on the screen.
3 Press the m/M buttons to select AUTO ADJUST and
press the OK button.
The AUTO ADJUST menu appears on the screen.
16
(GB)
(SCREEN) and