Seav LRX 2239 Handbuch Seite 8

procedure with the shutter closed: with the SEL key to the RIT.ANTE
LED when flashing, press the SET key, wait for the desired interval of
time, then press the SET key again; the fixed door delay time of 2 sec-
onds during opening is stored, the door delay time during closing is
stored for the programmed time and the RIT.ANTE LED is on.
To restore the initial configuration (without door delay) go to the
RIT.ANTE LED when flashing then press the SET key twice within 2 sec-
onds; the LED goes off and the operation is completed.
EXTENDED MENU 1
The control unit is supplied by the manufacturer with only the option of
directly selecting the functions listed in the main menu.
To enable the functions listed in extended menu 1, proceed as follows:
press the SET button and hold for 5 seconds; the T.PAUSA and RIT.
ANTE LEDs will flash in alternation and you have 30 seconds to select
the functions of Extended Menu 1 using the SEL and SET buttons; after
another 30 seconds, the control unit returns to the main menu.
EXTENDED MENU 1
Led reference Led off
A) TIPO MOTORE INB. CMD AP = OFF
B) AUTO PGM Electronic brake = ON
C) CODE Automatic
D) CODE PED. Aries effect = OFF
E) T. MOT. Closure effect = OFF
F) T.MOT.PED. Follow Me = OFF
G) T. PAUSA Flashing beacon ON/OFF in alternation
H) RIT. ANTE Flashing beacon ON/OFF in alternation
A) TYPE OF MOTOR
(command inhibition during opening and pause time, if entered) :
The command inhibition function during opening and pause time, if
entered, is used when automation includes the loop detector. During
opening or pause the control unit does not detect the commands given
by the loop detector at every passage.
The control unit is supplied by default with the command inhibition
function during opening and pause time not enabled. To enable the
function follow this procedure: check that the Extended Menu 1 is
enabled (the T.PAUSA and RIT ANTE LEDs start flashing in alternation),
use the SEL key to navigate to TIPO MOTORE when the respective LED
is flashing, and press the SET key: the TIPO MOTORE LED switches on
and programming is complete.
Repeat the operation to restore the previous configuration.
B) AUTO PGM (Electronic brake) :
The control unit is supplied by the manufacturer with the electronic
brake function disabled. To enable the function proceed as follows:
check that the extended menu 1 is enabled (the T. PAUSA and RIT
ANTE LEDs start flashing in alternation), use the SEL key to navigate to
AUTO PGM when the corresponding LED is flashing and press the SET
key: the AUTO PGM LED switches on and programming is complete.
The control unit reduces the forward motion of the gate due to inertia in
the presence of a stop or inversion command. Repeat the operation to
restore the previous configuration.
C) CODE (Automatic/Step-by-step operation):
The control unit has, by default, the operating logic for "automatic"
operation. To select the operating logic for "step-by-step" operation,
proceed as follows: check that the Extended Menu 1 is enabled (the
T.PAUSE and RIT ANTE LEDs start flashing in alternation), press the
SEL key until the CODE Led flashes, then press the SET key; the CODE
Led turns on and remains steady and programming is complete. Repeat
the operation to restore the previous configuration.
D) CODE PED. (Aries (ramming) effect) :
The control unit is supplied by the manufacturer with the aries (ram-
ming) effect function disabled. To enable the Aries (ramming) effect at
maximum power, proceed as follows: check the extended menu 1 is
enabled (the T.PAUSA and RIT ANTE LEDs flash in alternation), press
the SEL key until the CODE PED Led flashes, then press the SET key,
at the same time the CODE PED LED turns on and remains steady and
programming is complete. To enable the Aries (ramming) effect at the
power configured using the VR1 Trimmer, repeat the above procedure,
pressing the SEL key twice (the CODE PED Led flashes quickly) instead
of once. Repeat the operation to restore the previous configuration.
In this way the lock can be unlocked and the opening phase can be
executed correctly. Before starting the opening process, the control unit
sends a closing command for 2 seconds, at a power associated with
Led on
INB. CMD AP. = ON
Electronic brake = OFF
Step-by-step
Aries effect = ON
Closure effect = ON
Follow Me = ON
- 8 -
the selection.
E) T. MOT. (Closure strike):
The control unit is supplied by the manufacturer with the closure strike
function not enabled. To enable the function, proceed as follows: check
the extended menu is enabled (the T. PAUSA and RIT. ANTE LEDs flash
in alternation), press the SEL key until the T. MOT. LED flashes, then
press the SET key: the T. MOT. LED turns on and programming is com-
plete. If you wish to enable the Closure strike function at the configured
power with the VR1 trimmer, repeat the above procedure, pressing the
SEL key twice (the T.MOT. Led flashes quickly) instead of once. Repeat
the operation to restore the previous configuration.
If Deceleration during closing is programmed, the control unit will add
1-sec time at the power associated with the selection (after completing
the decelerated closing phase) in order to overcome the lock, if present.
F) T. MOT. PED. ( Follow Me ) :
The control unit is supplied by the manufacturer with the Follow Me
function not enabled. To enable the function, proceed as follows: check
the extended menu 1 is enabled (the T.PAUSA and RIT ANTE LEDs flash
in alternation), press the SEL button until the T.MOT.PED Led flashes,
then press the SET key; at the same time the T.MOT.PED LED turns on
and remains steady and programming is complete. In this way the con-
trol unit executes the closing phase immediately, ignoring the config-
ured operating logics, if it detects transit with activation of the photocell
connected to the DS input during the opening, Pause and Closing phas-
es.
Repeat the operation to restore the previous configuration.
EXTENDED MENU 2
The control unit is supplied by the manufacturer with only the option of
directly selecting the functions listed in the main menu.
To enable the functions listed in Extended Menu 2, proceed as follows:
open Extended Menu 1 (as instructed in the respective section), then
press and hold the SET key for 5 seconds; the T.PAUSA and RIT ANTE
LEDs flash at the same time; you have 30 seconds to select the func-
tions of Extended Menu 2 using the SEL and SET buttons; after anoth-
er 30 seconds, the control unit returns to the main menu.
EXTENDED MENU 2
Led reference Led off
A) TIPO MOTORE Remote PGM = OFF
B) AUTO PGM Photocell test= OFF
C) CODE Pre-flash and Cour. light=OFF Pre-flash or Cour. light=ON
D) CODE PED. Flash in Pause = OFF
E) T. MOT. PUL=PUL/PED=PED
F) T.MOT.PED. PUL=PUL / PED=PED
G) T. PAUSA Flash ON/OFF simultaneously
H) RIT. ANTE Flash ON/OFF simultaneously
A) TYPE OF MOTOR
(Remote programming of radio control):
The control unit enables remote programming of the transmission code,
without using the SEL key.
To program the transmission code in remote mode, proceed as follows:
send the previously stored radio control code continuously for more
than 10 seconds and the control unit will enter the programming mode
as described above for the CODE Led in the main menu.
The control unit is supplied by the manufacturer with remote program-
ming of the transmission code not enabled; to enable the function pro-
ceed as follows: check the extended menu 2 is enabled (the T. PAUSA
and RIT. ANTE LEDs flash simultaneously), press the SEL button until
the TIPO MOTOR LED flashes, then press the SET key, at the same time
the LED TIPO MOTOR turns on and remains steady and programming
is complete. Repeat the operation to restore the previous configuration.
B) AUTO PGM (Photocell Test):
The control unit is supplied by the manufacturer with programming of
the Photocell Test disabled; to enable the function (in accordance with
standard EN 12453), proceed as follows: check the extended menu 2 is
enabled (the T. PAUSA and RIT. ANTE LEDs flash simultaneously), press
the SEL button until the AUTO PGM Led flashes, then press the SET
key, at the same time the LED AUTO PGM turns on and remains steady
and programming is complete. In this way, the Photocell connected to
the DS input is tested before the automation starts any of the phases.
Repeat the operation to restore the previous configuration. If not used,
the DS input must be jumped and the Photocell Test disabled.
Led on
Remote PGM = ON
Photocell test = ON
Flash in Pause = ON
PUL=PUL/PED=DS AUX1/2
PUL=AP / PED=CH