Description Of The Machine And Planned Use; Safety Signs; Identification Label - Stiga CP1 430 Li D48 Gebrauchsanweisung

At the end of their working life, dispose of
batteries paying due attention to the envi-
ronment. Batteries contain material classified
as hazardous for you and the environment. They
must be removed and disposed of separately at a
facility that accepts lithium-ion batteries.
Separate waste collection of the products
and packaging used allows the materials to
be recycled and reused. Reuse of recycled ma-
terials help to prevent environmental pollution and
reduces the demand for raw materials.
3. GETTING TO KNOW THE MACHINE
3.1 DESCRIPTION OF THE MACHINE AND
PLANNED USE
This machine is pedestrian-controlled lawnmower.
The machine is essentially composed of a motor which
drives a cutting means enclosed in a casing, equipped with
wheels and a handle.
The operator is able to operate the machine and use the
main controls, always staying behind the handle at a safe
distance from the rotating cutting means.
If the operator leaves the machine, the motor and cutting
means will stop within a few seconds.
3.1.1 Intended use
This machine is designed and built to cut (and collect) grass
in gardens and grassy areas, with a height according to its
cutting capacity, driven by an operator walking behind it.
Generally speaking this machine can:
1. Mow the grass and collect it in the grass catcher bag.
2. Mow the grass and discharge it on the ground through
the rear part.
3. Mow the grass and discharge it on the ground laterally
(if available).
4. Mow the grass, chop it and discharge it on the ground
(mulching effect - if available).
The use of special attachments provided for by the Manu-
facturer as original equipment or which may be purchased
separately, allows this work to be done in various operating
modes, illustrated in this manual or the instructions that
accompany the single attachments.
3.1.2 Improper use
Any other usage different from the afore-mentioned ones
may be hazardous and harm persons and/or damage
things.
Examples of improper use may include, but are not limited
to:
– Allowing children, animals or other passengers
to ride on the machine as they could fall
off and injure themselves or compromise
safe driving by the operator.
– Letting oneself be transported by the machine.
– Using the machine to tow or push loads.
– Using the cutting means on surfaces other than grass.
– Use the machine for leaf or debris collection.
– Using the machine to trim hedges, or for
cutting vegetation other than grass.
– Use of the machine by more than one person.
IMPORTANT Improper use of the machine will invalidate
the warranty, relieve the Manufacturer from all liabilities,
and the user will consequently be liable for all and any dam-
age or injury to himself or others.
3.1.3 User types
This machine is intended for use by consumers, i.e.
non-professional operators.
It is intended for "DIY" use only.
IMPORTANT The machine must be used by one oper-
ator.
3.2

SAFETY SIGNS

The machine has various symbols on it (Fig. 2). Their func-
tion is to remind the operator of the correct conduct for use,
with due care and caution. Meanings of the symbols:
Warning. Read the instructions before
operating the machine.
Danger! Risk of thrown objects. Keep
all persons away from the work area whilst
working.
Only for lawn mowers with thermal engine.
Only for electric lawn mowers with mains
power supply.
Only for electric lawn mowers with mains
power supply.
Danger! Danger of cutting. Cutting
means in motion. Do not insert hands or
feet into the cutting means housing.
Be careful when using the sharp cutting
means. Do not put hands or feet near or
under the opening of the cutting means. The
cutting means continues to turn even after
the motor has been switched off. Remove
the safety key (deactivation device) before
any maintenance is carried out.
IMPORTANT Any damaged or illegible decals must be
replaced. Order replacement decals from an Authorised
Service Centre.
3.3

IDENTIFICATION LABEL

The identification label holds the following data (Fig.1).
1. Sound power level.
2. CE conformity marking.
3. Year of manufacture.
4. Type of machine.
5. Serial number.
6. Name and address of Manufacturer.
7. Article code.
8. Max. motor operation speed.
9. Weight in kg.
10. Power voltage and frequency.
11. Electrical protection rating.
12. Nominal power.
Write the identification data of the machine in the specific
space on the label on the back of the cover page.
IMPORTANT Quote the information on the product iden-
tification label whenever you contact an Authorised Service
Centre.
IMPORTANT The example of the Declaration of Con-
formity is provided on the last pages of the manual.
EN - 3